Manual Eurom Siena (page 16 of 44) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

474862

Zoom out

Zoom in

1/44

Operating with the buttons:

 Pressing the button switches the atmospheric lighting on. The red light next to the button will be

illuminated. Pressing this button again will switch the atmospheric lighting off. If you press the

button for longer than three seconds, the dimmer function will start to work: the brightness of the light will

gradually increase and then decrease. Release the button when the lighting reaches the desired intensity.

 Pressing the '900W' button sets the heating at half capacity (900 Watt). The red light next to the button will

be illuminated and the ventilator will start to distribute warm air via the upper grille.  This function

only works if the atmospheric screen is working! Pressing this button again will switch the heating off but the

atmospheric lighting will continue to work.

 1800W1800 Watt). The red light next to the button will

be illuminated and the ventilator will start to distribute warm air via the upper grille.  This function

only works if the atmospheric screen is working! Pressing this button again will switch the heating off but the

atmospheric lighting will continue to work.

 Every time you press a button you will hear a 'beep' and this indicates that the fireplace has 'picked up' the

command.

Operating using the remote control:

It takes a little time before the receiver responds to a signal transmitted from the remote control. Do not press a

button more frequently than once per two seconds as this will disrupt the function.

 You switch the atmospheric lighting on and off using the red button on the remote control.

 The black buttons '900W' and '1800W' have the same function as the '900W' and '1800W' buttons on the

fireplace (see above).

 Pressing and holding the black 'dimmer' button increases and decreases the brightness of the light. Release

the button when the lighting reaches the desired intensity.

 Every time you press a button you will hear a 'beep' and this indicates that the fireplace has 'picked up' the

command.

 When you switch a particular function on using the remote control, the red light next to the corresponding

button on the fireplace will be illuminated.

Warning: This heater is not equipped with a device to control the room temperature. Do not use this heater in

small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant

supervision is provided.

Replacing a bulb

 Always unplug the fireplace before replacing a bulb!

 The bulbs get hot during use; allow plenty of time for them to cool down before touching them!

 Two people are required to replace a bulb.

 Carefully remove the glass plate in front of the fireplace by lifting it off its hooks. Put it somewhere safe.

 We advise you to now take the fireplace off the wall. In order to do so, the two screws which attach the

fireplace to the lower spacer bracket must be removed. Lie the fireplace down on a flat, clean surface.

 Under the 'fire' there is a cover place which covers the bulbs. Remove the 5 screws from this cover plate

and remove cover plate.

 You must remove the flexible rotator in order to gain access to the bulbs. Pinch the clamp on the right hand

side and move to the left, away from the rubber. Now slide the rubber off the axle (to the left). Once this is

free of the axle, gently pull forwards and slide/pull gently to the right (out of the left hand side attachment

point).

 Remove the broken bulb and replace with a 40Watt G9 halogen bulb. Never touch a halogen bulb with bare

hands!

 Replace the rotator by following the instructions above in reverse order.

 Screw on the cover plate, hang the fireplace on the wall supports and screw in the screws which attach the

fireplace to the spacer bracket. Finally, replace the glass plate on the hooks, in front of the fireplace.

 The lamp may only be replaced by a person qualified to do so.

Safety feature

The Siena atmospheric fireplace is equipped with a double overheating safeguard.

One overheating safeguard switches the heater off if it overheats internally.This may occur if the heater cannot

give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused by

(partially) covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a

wall or something similar.

If this happens, turn the fireplace off by switching the main switch to O and remove the plug from the socket.

Leave the fireplace to cool down for at least 15 minutes and remove the cause of overheating. You can then

switch the fireplace back on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Siena in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom Siena Manual

Product: