Manual Eufab 11555 - Amber III (page 10 of 44) (English, German, Dutch, French, Italian, Polish, Spanish)

807227

Zoom out

Zoom in

1/44

Inserting the license plate

Mounting the frame holder

Mounting the license plate holder

Undo the handle screw of the frame holder and rotate out fully. Open the cu

of the frame holder and place the inserts around the U-bracket at a position

suitable for your bicycle. Place the cu around the inserts and push  rmly

together. Close the frame holder using the handle screw (but do not tighten).

Remove the screws from the lamp mount before installing the license plate

holder and then mount the license plate holder.

The license plate holder must be at the same height as the lights.

Step 3

Components

Laying electrical cables

The mounting clips for securing the license plate are push-out parts in the

holder. Break out two of the clips. Slide the license plate into the holder, then

push the clips into the cut-outs to secure the license plate.

Attaching the plastic covers

Mounting the bicycle rack on the trailer tow bar

Fit the plastic covers onto the middle of the wheel rails.

Before you put the bicycle rack on the trailer tow bar, familiarise yourself with

the quick locking system.

Ensure that the trailer tow bar is undamaged, clean and free of grease.

The quick locking mechanism is a component with a lever. Activating the lever

opens or closes the quick locking mechanism. With the help of the securing

bolt and the padlock, the quick locking system may be locked and secured.

Mounting the short tensioning straps

Insert the short tensioning strap from the inside to the outside below the bike

holder and then from the outside to the inside through the slots of the bike

holder (see photograph).

Set bolt Lock nut

Set bolt Safety pin

Caution: You must tighten both knob nuts very  rmly to ensure that the

U-bracket is  ush against the U-bracket mount.

Lever

Lock

Clips Cut-outsCut-outs

The padlock must always be used as additional security

when using the bicycle rack.

Park your vehicle on a level surface.

Switch the motor o and pull on the brake.

Remove the securing bolt from the quick locking mechanism and rotate by

90° to prevent it from engaging again. Open the quick locking mechanism by

lifting the lever.

Place the rack, from above, horizontally onto the trailer tow bar. Push the

lever of the quick locking mechanism down (force required is approximately

35 - 40kg) as far as it will go (the lever will remain in the horizontal position).

Check whether the bike rack is securely and  rmly positioned on the trailer

tow bar and can no longer be rotated. If this is not the case, the quick locking

mechanism must be readjusted. Lift the lever and remove the rack from

Secure the cables of the lights to the underside of the rack using the supplied

cable ties. Make sure that the cables cannot be damaged when lowering and

raising the rack.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 11555 - Amber III in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eufab 11555 - Amber III Manual

Product: