Manual Eufab 11555 - Amber III (page 9 of 44) (English, German, Dutch, French, Italian, Polish, Spanish)

807227

Zoom out

Zoom in

1/44

6. MOUNTING THE BICYCLE RACK

The bicycle rack must  rst be assembled. Take all of the components out of the

packaging and set them out clearly. Every stage is described and clearly shows

which components are required for the assembly of the rack.

Step 1

Components

Personal injury or property damage due to loss of the bicycle rack

while driving.

A loose or faulty connection between the bicycle rack and trailer tow bar can

lead to the detachment of the bicycle rack.

• Replace a defective trailer tow bar.

• Clean the trailer tow bar of dirt, dust and grease.

The general operating permit must be carried in the

vehicle when the rack is mounted.

Do not travel with the bicycle rack empty. Store it in

the boot of your vehicle. This prevents increased fuel

consumption and protects the rack.

The driver is always responsible for ensuring that the

load and the load securing meet the regulations.

Personal injury or property damages caused by increased wind loads

The bicycle rack and trailer tow bar may be damaged by too high a wind load.

• Remove all bags from the bicycle before starting your journey.

• Do not use protective covers for the bicycle during the journey.

Assembly

Two wheel rails form a pair. Place three pairs of wheel rails, with the plastic

shells on the outside, so that they are parallel on the base frame and the

drilled holes in the rail match the holes in the base frame. Secure each wheel

rail to the base frame with the lock screws M6 x 50, washers and self-tapping

nuts M6.

Join the two halves of the lamp mount set together. This is made easier by

the small guide element which is already mounted on one side. Push the rails

together and secure the connection with the cross-headed screw (M5x12),

spring washer and washer.

Insert the cross-headed screws M5 x 35 with spring washers and washers,

from below, through the vertical drilled holes of the lamp mount. Insert the

screws through the threaded holes on the underside at the end of the lamp

mount. Tighten the screws.

Make sure that the fog light is installed on the left side of the mount!

Step 2

Components

Assembly

Place the U-bracket on the U-bracket mount of the base frame. Secure the

U-bracket with the supplied lock screws (M8 x 60), washers and knob nuts

M8. The knob nuts must be mounted on the inside (see photograph).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 11555 - Amber III in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eufab 11555 - Amber III Manual

Product: