722072

Enduro AS101 Manual

39
Zoom out
Zoom in
Previous page
1/48
Next page
ENDURO
®
autoSteady 32
Ref: AS101-UM-TKI-0114-Rev. A
Ensure that there is no force and movement on the cables. Also avoid any loops.
Route the motor cables along the underside of the caravan floor, and through the drilled hole.
Protect the electrical cables against sharp edges (for example near the chassis) by the supplied convoluted
cable trunking (26). Please can cut the trunking to the correct length.
Secure the motor cables and the cable trunking (26) under the body of the caravan by using the cable ties (17)
or P-Clips (14 & 15) and screws (13).
Please ensure the motor cables are fixed very tightly near the corner steady, and the cables
do not interfere with any part of corner steady when it is drawn back completely.
Once the motor cables are through the drilled hole next to the control unit (6), cut the cables. Ensure that they
are all the same length. Remove approx. 5mm of the insulation from the ends. Fix the spade fork connectors
(23) on the motor-cable ends by using crimping pliers. A secure and good quality connection on each cable is
essential.
Attach the spade fork connectors to the terminals on the control unit (see wiring diagram Fig. 8) and fix them
tightly by the screws. A safe and good quality connection on each cable is again essential.
Find a suitable place for the battery power isolation switch (24) which includes an external holder with hinged
cover. Important: The switch must be mounted onto the exterior body of the caravan and be easily
accessible from the outside of the caravan in case of any emergency. The switch must be mounted close
to the location of the battery in order to keep the length of the battery cables to a minimum.
Use the cardboard template to position the hole positions and the drill holes. Mount the switch and the housing
with the bolts, washers and nuts, and finally mount it on the caravan with stainless steel screws (13).
Route the positive (+) power cable (including fuse) from the battery to the battery power isolation switch (24)
and then further to the control unit (6).
Cut the positive power cable to an appropriate length and remove approx. 5mm of the insulation from the ends.
Fix the O-ring connectors (22) by using crimping pliers. A secure and good quality connection on each cable is
essential.
The electronic connections of the battery power isolation switch (24) must be covered by the supplied rubber
isolation shells (25).
Route the negative (-) power cable directly from the battery to the control unit (6).
No cables may be routed over the control unit!
Again it is recommended to use the supplied trunking (26) to protect the cables against sharp edges. Attach the
cables and trunking with the cable ties (17) or P-clips (14 & 15) and P-clip screws (13).
Cut the cables to an appropriate length and remove approx. 5mm of the insulation from the ends. Fix the spade
connectors (23) by using crimping pliers. A secure and good quality connection on each cable is essential.
Connect the battery cables (19 & 20) to the control unit (6): Attach the spade fork connectors to the positive
(+) en negative (-) terminal of the control unit and fix them tightly by the screws.
Connect the battery cables to the existing battery terminals (red = positive, black = negative). Two types of
battery terminal connector (21 & 22) are provided for use as appropriate.
Caution! Make sure that you do not reverse the positive (+) and negative (-) connections.
Incorrect connection (reverse polarity) will result in damage to the control unit.
Seal 25mm hole in vehicle under body using plastic body sealant.
Next you can connect the cable for the emergency draw back function (option, not obliged). If you forget to
draw back the corner steady before you start to drive, the corner steady or your caravan can get significant
damage. This emergency draw back function ensures that (if installed properly!) the corner steady will be
drawn back automatically when the caravan is connected on the constant 12V power source of the car (via 7 or
13 pin plug).
Connect one end of the blue cable for the emergency draw back function (18) to the constant power source
(+12V) of the car (via 7 or 13 pin connector) and not in direct connection is with the caravan battery! You can
also find this constant power source in the 12V central distribution box of your caravan. It is normally used to
use your refrigerator during driving. If necessary measure again with a multimeter.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro AS101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro AS101 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info