722072

Enduro AS101 Manual

38
Zoom out
Zoom in
Previous page
1/48
Next page
ENDURO
®
autoSteady 31
Ref: AS101-UM-TKI-0114-Rev. A
Check if every pin on the spindle has been mounted tightly enough and all the parts of the
corner steady are under good condition.
Mount the corner steady back to the bottom of the caravan (chassis) via the existing holes on the bracket (Fig.
7A) of corner steady with the original bolts/nuts. If the original bolts are not long enough to be matched with
the original washers and nuts, please use the supplied alternative flange nuts (27) to replace the original
washers and nuts.
Fully tighten all the nuts and bolts.
Adequate ground clearance: Please notice that the minimum distance between the lowest
line of corner steady and ground is 110mm, no matter what kind of chassis or installation
situation.
Re-check that all bolts/nuts have been tightened!
Mount the ground support plates (11) on the feet of the corner steady with the supplied pins and clips (Fig. 6)
The main mechanical components have now been installed.
INSTALLATION - ELECTRICAL/ELECTRONIC COMPONENTS
Make sure the 12V supply from the battery and any 230V electricity supply are disconnected.
Remove battery cable terminals and disconnect any external electrical power before starting work.
Find a suitable place for the electronic control unit (6), such as a storage area, under a seat or a bed. Make
sure this place is dry and close to the battery (40cm to 60cm). The electronic control unit can be mounted
vertically on a side wall or be mounted flat. When mounted vertically, the connections must point downwards to
avoid any short-circuits by objects falling into.
Fix the electronic control unit (6) securely into position with two screws (12). Note: if the provided screws are
not of suitable length or type for the desired location/material please substitute these as appropriate.
Drill a 25mm hole through the floor of the caravan approximately 150mm centrally in front of the control unit
terminals.
Caution! Take extra care to avoid any chassis members, gas pipes and electrical wires!
Route and connect the motor cables and battery cables in accordance with wiring diagram (Fig 8, top view of
the caravan).
The motor cables have been pre-wired already to each motor (just the motor side). Red = Positive (+) and
black is negative (-).
Open the cover on the control unit (Fig. 9A), to find the connectors for the wires.
The connectors on the electronic control unit (6):
Terminal A-
Terminal A+
Terminal B-
Terminal B+
Terminal C-
Terminal C+
Terminal D-
Terminal D+
Terminal 12V-
Terminal 12V+
Terminal e
Terminal N
Left front motor (-)
Left front motor (+)
Left back motor (-)
Left back motor (+)
Right front motor (-)
Right front motor (+)
Right back motor (-)
Right back motor (+)
Main power (-)
Main power (+)
Automatic draw back function
Not used
See also wiring diagram (Fig. 8).
Notice: Left side means the driver side for Europe continent and the passenger side for the UK.
Mark the motor cables for all motor units using the cable number markers (16). Cable number markers “A” for
left-front motor, “B” for left-back motor, “C” for right-front motor, “D” for right-back motor (Fig. 8).
Caution! Make sure that you do not reverse the positive (+) and negative (-) connections.
Incorrect connection (reverse polarity) can result in damage to the control unit!
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro AS101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro AS101 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info