Manual Elro AP5500 - Pro Alarm System (page 14 of 49) (English)

708667

Zoom out

Zoom in

1/49

Detector will not illuminate when the Detector is

triggered, (unless in test mode). However, under low

battery conditions this LED will be illuminated for

approx. 1 second when the detector is triggered.

When this occurs the batteries should be replaced as

soon as possible.

The Magnetic Contact Detector has the facility to

connect an additional wired Magnetic Contact. This

additional contact must be of a normally closed contact

type with the contacts being opened in order to

generate an alarm condition.

Any number of Magnetic Contact Detectors can be

used with the system, providing they are all coded with

the system house code and are mounted within

effective radio range of the Control Panel.

CHOOSING A MOUNTING LOCATION

The Magnetic Contact Detector is suitable for mounting

in dry interior locations only.

Decide which doors/windows are to be protected by

fitting Magnetic Contact Detectors, (usually the front

and back doors as a minimum will have Magnetic

Contact Detectors fitted). Additional detectors may

also be fitted where required to other vulnerable doors

or windows, (e.g. garage, patio/conservatory doors

etc).

Ensure that the position selected for the Magnetic

Contact detector is within effective range of the Control

Panel, (refer to ‘Testing the Control Panel & Remote

Control’).

Note: Take care when fixing the Detector to a metal

frame, or mounting within 1m of metalwork (i.e.

radiators, water pipes, etc) as this could affect the radio

range of the device. If required, it may be necessary

to space the magnet and detector away from the metal

surface using a plastic or wooden spacer to achieve the

necessary radio range.

INSTALLING THE MAGNETIC CONTACT

DETECTORS

Ensure that the system is in Test Mode.

1. Remove the battery cover by sliding and lifting it off.

(DO NOT use a screwdriver to lever the cover off)

2. Remove the battery holder by carefully tilting up the

end and pulling the connector off of the printed

circuit board.

3. Mount the Detector to the fixed part of the frame

along the opening edge opposite the hinges using

either the double sided adhesive tape or screws

provided.

If fixing the Detector with screws; fit the Keyhole

slot in the top of the Detector over the head of the

smaller pan-head screw. Secure the bottom of the

Detector using the 12mm countersunk head screw

fitted within the battery compartment. You will

need to drill out the centre of the fixing screw hole

using a 3mm drill. Do not over-tighten the fixing

screws as this may distort or damage the casing.

4. Fit the Magnet to the moving part of the

door/window opposite the Detector using the

adhesive tape or 15mm fixing screws. Ensure that

the parallel gap between the Magnet and Detector

is less than 10mm and that the arrow on the

Magnet is pointing towards and aligned with the

mark on the Detector.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro AP5500 - Pro Alarm System Manual

Product: