708667

Elro AP5500 - Pro Alarm System Manual

15
Zoom out
Zoom in
Previous page
1/49
Next page
5. If an additional wired Magnetic Contact is required,
this should be wired to the terminal block provided
in the battery compartment. The wired contact
should be connected using two core (24AWG) wire
of maximum length 1.5m.
A cable entry cut-out is provided beside the
terminal block in the battery cover.
6. Slide the batteries supplied into the battery holder,
ensuring that the positive (+) side is uppermost on
each battery as it is installed.
7. Carefully refit the battery holder onto the Detector
ensuring that the spring connectors slide onto
either side of the circuit board.
8. Refit the battery cover.
SETTING THE MAGNETIC CONTACT
DETECTORS
1. Located in the battery compartment is a row of 11
DIP switches.
2. DIP switches 1-8 are used to set the House Code
for the Magnetic Contact Detector and must be set
to the same ON/OFF combination as the House
Code DIP switches in all other system devices.
3. Configure the alarm zone which the detector will
operate on with DIP switches 9-11 as follows:
DIP 9
DIP 10
DIP 11
Zone 1
OFF
OFF
OFF
Zone 2
OFF
OFF
ON
Zone 3
OFF
ON
OFF
Zone 4
OFF
ON
ON
Zone 5
ON
OFF
OFF
Zone 6
ON
OFF
ON
Note: If the setting of DIP switches 9-11 does not
conform to any of the above mentioned six criteria,
the Control Panel will not receive a trigger signal
from the magnetic contact detector.
4. If additional external contacts are wired to the
Detector, remove the jumper link S2 on the PCB.
IMPORTANT: If external contacts are not
connected, then jumper link S2 must be fitted for
the detector to operate correctly.
TESTING THE MAGNETIC CONTACT
DETECTORS
Ensure that the system is in Test Mode
1. Use the and buttons to scroll
through the menu until ‘WALK TEST’ is displayed.
Press to activate Walk Test.
‘Walk Test Waiting…’ will be displayed.
2. Remove the battery cover by sliding off.
As the battery cover is removed the LED on the
Detector will illuminate for approx. 1 second to
indicate that the tamper switch has been activated.
In addition, the Control Panel will beep to indicate
that an alarm signal has been received and
‘Accessory Tamper’ will be displayed.
3. Open the door/window to detach the magnet from
the Detector. As the magnet is parted from the
detector the LED will illuminate for approx. 1
second to indicate that the Detector has been
triggered. In addition, the Control panel will beep
to indicate that an alarm signal has been received
and the identity of the zone that the detector is set
for will be displayed.
Note: In normal mode with the battery cover fitted,
the LED on the detector will not illuminate when the
detector is triggered, (unless the battery is low).
4. If connected, operate the wired Magnetic Contact.
As the contact is opened the LED on the Detector
should illuminate for 1 second to indicate that it has
been triggered and the Control Panel will
acknowledge the alarm signal.
5. Refit the battery cover on the Detector.
6. Press to return to the top level menu of
TEST MODE.
13
ON
ECE
1 2 3 4 5 6 7 8 9 10 11
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AP5500 - Pro Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info