708667

Elro AP5500 - Pro Alarm System Manual

11
Zoom out
Zoom in
Previous page
1/49
Next page
where you plan to install detectors. Check that the
Control Panel acknowledges the signal from the
Remote Control each time the ‘DISARM’ button is
pressed.
5. Press to return to the top level menu of
TEST MODE.
PASSIVE INFRARED DETECTORS
PIR detectors are designed to detect movement in a
protected area by detecting changes in infra-red
radiation levels caused, for example, when a person
moves within or across the devices field of vision. If
movement is detected an alarm signal will be emitted,
(if the system and alarm zone is armed).
Note: PIR detectors will also detect animals, so ensure
that pets are not permitted access to areas fitted with
Passive Infra-Red Detectors when the system is
armed.
Any number of PIR Detectors can be used with your
system, providing they are all coded with the system
house code and are mounted within effective radio
range of the Control Panel.
The PIR Detector uses a PP3 Alkaline battery which
under normal conditions will have typical life of up to 1
year. When the battery level drops, with the PIR in
normal mode and the battery cover fitted, the LED
behind the detection window will flash. When this
occurs the batteries should be replaced as soon as
possible.
CHOOSING A MOUNTING LOCATION
The recommended position for a PIR Detector is in the
PCB Position
Range
1
6m
3
9m
5
12m
Note: The range as indicated above refers to the
linear distance in front of the PIR sensor.
When considering and deciding upon the mounting
position for the detector the following points should be
considered to ensure trouble free operation:
1. Do not locate the detector facing a window or
where it is exposed to or facing direct sunlight.
PIR Detectors are not suitable for use in
conservatories.
2. Do not locate the detector where it is exposed to
ventilators.
3. Do not locate the detector directly above a heat
source, (e.g. fire, radiator, boiler, etc).
4. Where possible, mount the detector in the corner of
the room so that the logical path of an intruder
would cut across the fan detection pattern. PIR
detectors respond more effectively to movement
across the device than to movement directly
towards it.
corner of a room mounted at a height between 2 and
2.5m. At this height, the detector will have a
maximum range of up to 12m with a field of view of 110°.
The position of the PCB inside the PIR can be set to 5
different positions to adjust the range of the detector.
Setting the PCB in position 3 will reduce the range to
9m approximately, with position 1 providing a range of
6m approximately. The recommended position setting
for the PCB is in position 5.
12
10
8
6
4
2
Less Sensitive More Sensitive
5. Do not locate the detector in a position where it is
subject to excessive vibration.
6. Ensure that the position selected for the PIR
110¢X
0
TOP VIEW
2
4
6
8
10
12
detector is within effective range of the Control
Panel, (refer to ‘Testing the Control Panel &
Remote Control’).
12 10 8 6 4 2 0
UNIT:M
2
SIDE VIEW
9
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AP5500 - Pro Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info