Manual Elro AP5500 - Pro Alarm System (page 9 of 49) (English)

708667

Zoom out

Zoom in

1/49

6. If the telephone based functionality is to be used

then the Control Panel will need connecting to a

convenient telephone point.

LCD Display Window

Keypad Status LEDs

LCD Control Panel – Keypad and LED Layout

Note: It is recommended that the telephone

connection lead is not extended beyond 5m before

connecting to a telephone master or secondary

outlet.

7. Do not locate the Control Unit closer than 1m to

any large metallic object, (e.g. mirrors, radiators,

etc) as this may affect the radio range of the

Control Panel.

MOUNTING THE CONTROL PANEL

1. Undo the two captive fixing screws on top of the

panel and open the cover. The cover is hinged

along the bottom edge.

2. Unclip and remove the two back-up batteries on

either side of the panel.

3. Hold the Control Panel in position on the wall and

mark the positions of the four fixing holes.

Remove the Panel and drill four 5mm holes and fit

the 25mm Wall Plugs.

IMPORTANT: Do not drill the fixing holes with the

Control Panel in position; as the resulting dust and

vibration may damage the Control Panel’s internal

components and invalidate the guarantee.

4. Fit two 18mm No.4 screws into the top holes until

almost fully home and hang the Control Panel over

these screws using the two keyhole slots in the top

corners of the panel casing.

5. Route the cable from the Power Supply Unit up

behind and on the right hand side of the Control

Panel and connect the plug to the DC power

socket in the panel. Ensuring that the cable is not

trapped between the panel and the wall.

6. Fix the Panel to the wall using two 18mm No. 4

screws in the lower two fixing holes in the panel

and tighten the upper fixing screws until they just

grip the casing. Do not over tighten the fixing

screws as this could damage or distort the casing.

7. Ensure that the ‘Reset’ and the ‘Hard-Wired

Siren tamper detect’ jumper links are set in the

OFF position.

8. Connect battery leads to both back-up batteries

and refit batteries.

Battery 1 (left): Red lead to +ve battery terminal

Blue lead to –ve battery terminal

Battery 2 (right): Blue lead to +ve battery terminal

Black lead to –ve battery terminal

IMPORTANT: Take care when connecting battery

leads to the batteries as connecting incorrectly

could damage the batteries or the Control Panel.

Note: The Power LED may flash to indicate that

the unit is being operated from the back-up

batteries and that mains supply is not present.

9. If fitted, remove the plastic film covering the LCD

display and on the display window on the cover.

10. Close the lid of the Control Panel and tighten the

captive fixing screws.

11. Plug in and switch ON the Power Supply Unit, (the

Power LED should illuminate).

12. If required, connect the Control Panel to the

telephone line using the cable supplied by inserting

the small RJ11 plug into socket marked LINE

located on the bottom edge of the Control Panel.

If the cable supplied is not long enough to reach a

suitable phone point then it will need extending

using a coupler and extension lead (not supplied).

Note: If the Panel Tamper alarm sounds during the

installation reset the alarm by pressing:

, ,

on the Control Panel Keypad.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro AP5500 - Pro Alarm System Manual

Product: