663878

EdgeCraft Chef-s Choice - Commercial 2100 Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
symmetrical. Generally in Stage 1 you will find that only one pull in each (left and right)
slot is adequate. Before proceeding to Stage 2, carefully check the edge of your knife to be
sure a burr has been formed along the sharpened edge, as described next:
Detecting the Burr
In order to confirm that a burr (Figure 6) exists along one side of the edge, move your
forefinger carefully across the edge as shown in the Figures 6 & 7.
(Do not move your finger along the edge – to avoid cutting your finger). If the last pull was
in the right slot, the burr will appear only on the right side of the blade (as you hold it) and
vise versa. The burr, when present, feels like a rough and bent extension of the edge; the
opposite side of the edge feels very smooth by comparison. If a burr exists, proceed to
Stage 2.
If no burr exists, make one (1) additional pull in the left and right slots of Stage 1. Slower
pulls will help develop the burr. If the knife is extremely dull, additional pulls in Stage 1 may
be needed to develop a burr. Confirm the presence of the burr along the entire edge before
proceeding to Stage 2.
Stage 2: Using the above procedure described for Stage 1, sharpen the blade in Stage 2.
Pull the blade once through the left slot of Stage 2 (Figure 8) and once through the right
slot (Figure 9). For an eight (8) inch blade take about four (4) seconds for each pull. For
longer knives take about 6 seconds per pull and about 2-3 seconds for shorter blades.
Check for a burr along the edge. If no burr exists make additional pairs of pulls in Stage 2
until a burr develops and before proceeding to Stage 3.
Stage 3: In general only one or two pairs of pulls in Stage 3 will be necessary to obtain a
razor sharp edge. As in Stages 1 and 2, make alternate pulls in left (Figure 10) and right
slots pulling the knife through the slots at the same speed used in Stages 1 and 2.
More pulls in Stage 3 will refine the edge further, creating an edge particularly desirable for
the finest food preparations. Fewer pulls in Stage 3 may be preferable if you will be cutting
fibrous foods as discussed in more detail in the following sections.
After sharpening in Stage 3 the edge should be astonishingly sharp. There should be no
burr remaining along the edge.
Figure 9. Inserting blade in right slot of Stage 2. Figure 10. Inserting blade in left slot of Stage 3.
Alternate left and right slots.
9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Commercial 2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Commercial 2100 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info