Manual Dolmar AR-3733 (page 12 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598403

Zoom out

Zoom in

1/100

12 ENGLISH

tothe“I"(on)positionagain,thenpulltheswitchtrigger

two times to release the lock.

Opening angle selector lever

►Fig.6: 1. Opening angle selector lever

Bytiltingtheopeningangleselectorlevertotheleft

side, you can open the upper shear blade wider.

Tolimittheuppershearbladeopeningangle,rstpull

theswitchtriggerfully,andthenreturntheopening

angle selector lever to straight position.

Cutting depth adjustment

CAUTION: Do not let your hands or part of

body close to the shear blades. Otherwise per-

sonal injury may result.

Aftersharpeningorreplacingtheshearblade,adjust

cuttingdepthifnecessary.

Turnonthetool,andpulltheswitchtriggertwotimesto

opentheshearblades,andthenpresstheI/Oswitchto

the“O"(off)position.

Todeepenthecuttingdepth,turnthecuttingdepth

adjustingscrewclockwisewiththehexwrench.Andto

make the cutting depth shallower, turn the cutting depth

adjustingscrewcounterclockwise.

►Fig.7: 1.Cuttingdepthadjustingscrew

NOTE:Checkthecuttingdepthafteradjustment.If

the cutting depth is too shallow, the branch may not

cutfully.

Pilot lamps on the switch box

►Fig.8: 1.I/Oswitch 2.Pilotlamp(green) 

3. Pilot lamp (red)

Thegreenandredlampsindicateasfollows:

(On:

Off: Blinking: )

• Greenlamplightsup:thetoolisturnedon.

Green Red

• Greenlampblinks:thetoolisoverheated.Letthe

toolcooldownbeforeturningthetoolonagain.

Green Red

• Greenlamplightsupandredlampblinksorlights

up:batteryisloworalmostat.Chargethebatter-

ies.Wheneitherofthebatterybecomeslow,the

redlampblinksevenoneofthebatteriesisfull.

Green Red

• Greenlampandredlampblinkalternately:thetool

detectsbreakingofwire.Checktheconnection

cordforlooseconnectionwiththeswitchboxand

theshears.Ifthelampsstillblinkalternately,stop

using the tool immediately, disconnect the connec-

tion cord, remove the battery, and ask your local

authorizedservicecenterforrepair.

Lamps blink alternately

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing the battery holder into the

backpack

►Fig.9: 1. Clamp 2. Battery holder 3. Strap

1. Pass the switch box through the opening (either

rightorleft)ofthebackpack.

2. Passtheclampthroughthesquareholeofthebat-

tery holder, and secure the battery holder with the strap.

Make sure that the battery holder sits in the backpack

rmly.

Installing the holster

►Fig.10: 1. Holster 2. Strap

Passthebeltofthelowerbucklethroughtheopeningof

the holster.

Adjusting the harness

Adjusttheharnessasfollows:

1. Closeandlockthelowerbuckle,andadjustitsbelt

length.

►Fig.11: 1. Lower buckle

2. Adjusttheshoulderstraplength.

►Fig.12

3. Adjustthepositionoftheupperbuckle.Closeand

locktheupperbuckleandadjustitsbeltlength.

►Fig.13: 1.Upperbuckle

CAUTION: In case of emergency, quickly

open the lower buckle and upper buckle, loosen

shoulder straps, and set down the backpack.

Installing the connection cord

CAUTION: Always make sure that the switch

box's I/O switch is on the "O" side before attach-

ing the connection cord.

CAUTION: Do not operate the tool if the con-

nection cord is damaged.

NOTICE: Do not abuse the connection cord. Do not

carry the tool by pulling the connection cord. Keep the

connectioncordawayfromheat,oil,orsharpedges.

Otherwise the connection cord may be damaged.

Attach the connection cord with the switch box and the

shearsasfollows:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar AR-3733 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar AR-3733 Manual

Product: