598403

Dolmar AR-3733 Manual

11
Zoom out
Zoom in
Previous page
1/100
Next page
11ENGLISH
►Fig.2: 1. Red indicator 2. Button 3. Battery
cartridge 4. Battery holder
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
withalittleclick.Ifyoucanseetheredindicatoronthe
uppersideofthebutton,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen.Ifnot,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
not being inserted correctly.
NOTE:Thetooldoesnotworkwithonlyonebattery
cartridge.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotection
system.Thissystemautomaticallycutsoffpowerto
themotortoextendtoolandbatterylife.Thetoolwill
automaticallystopduringoperationifthetoolorbattery
isplacedunderoneofthefollowingconditions.Insome
conditions, the lamps on the switch box lights up.
Overload protection
Whenthetoolisoperatedinamannerthatcausesitto
draw an abnormally high current, the tool automatically
stops without any indication. In this situation, turn the
tooloffandstoptheapplicationthatcausedthetoolto
becomeoverloaded.Thenturnthetoolontorestart.
Overheat protection
Whenthetoolisoverheated,thetoolstopsautomati-
cally, and the green lamp on the switch box blinks. In
thissituation,letthetoolcooldownbeforeturningthe
tool on again.
Overdischarge protection
Whenthebatterycapacitybecomeslow,thetoolstops
automatically. And the red lamp on the switch box lights
uporblinks.Iftheproductdoesnotoperateevenwhen
theswitchesareoperated,removethebatteriesfrom
the battery holder and charge the batteries.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
►Fig.3: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
catetheremainingbatterycapacity.Theindicatorlamps
lightupforfewseconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
may have
malfunctioned.
NOTE:Dependingontheconditionsofuseandthe
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Switch action
CAUTION: Before connecting the battery to
the shears, always check to see that the switch
trigger actuates properly and returns to the “OFF”
position when released.
CAUTION: When not operating the tool,
always make sure that the I/O switch is on the "O"
side.
CAUTION:
Do not press the I/O switch to the
“I" (on) position while pulling the switch trigger.The
bladeclosesslightlyanditmaycausepersonalinjury.
Toturnonthetool,performasfollows:
1. Connect the switch box, connection cord, and
shears.(Referto“Installingtheconnectioncord”.)
2. Holdtheshearsrmly,andpresstheI/Oswitchto
the“I"(on)position.Thegreenpilotlamplightsup.
►Fig.4: 1.I/Oswitch 2.Pilotlamp(green)
3. Pilot lamp (red)
3. Theshearbladesarelocked-modewhentheI/O
switchison.Toreleasethelock,pulltheswitchtrigger
twotimes.Theuppershearbladeopensautomatically.
4. Toclosetheshearblade,pulltheswitchtrigger.
►Fig.5: 1. Switch trigger
Auto locked-mode and shut-off
mode shift
Forsafetyreasons,thetoolshiftsintolocked-modeor
shut-offmodeautomaticallyifthetoolisleftuntouched
foracertainperiodoftime.
After5minutes:Thetoolshiftsintolocked-mode.Pull
the switch trigger two times to release the lock.
After15minutes:Thetoolisshiftintoshut-offmode,
andthegreenpilotlampturnsoff.PresstheI/Oswitch
tothe“O"(off)positiononce,andpresstheI/Oswitch
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar AR-3733 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar AR-3733 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info