598403
14
Zoom out
Zoom in
Previous page
1/100
Next page
14 ENGLISH
Blade maintenance
NOTICE:Failuretoperformblademaintenancemay
causeexcessivebladefrictionandshortentheoper-
ating time per battery charge.
Beforeandafteroperation,checktheshearblades
carefully.
Afteroperation,cleanoffthebladeswithastiffbrush.
Thenwipethebladeswithacloth.AndapplyDolmar
genuine machine oil onto the blade edge and movable
part.
Fig.22
Sharpening blades
Upper shear blade
1. Applytheatsurfaceofthediamondletothe
blade edge.
Pushthediamondletowardsthetipofthebladeto
sharpen along the entire blade edge.
Maintainthesameatcontactwiththeleconsistently
along the entire blade edge.
Fig.23: 1.Diamondle
2. Applytheatsurfaceofthediamondlelightlyto
theoppositesideoftheblade.
Movethediamondletowardsthetipoftheblade
lightly to remove burrs.
Fig.24
NOTICE: Do not sharpen this side too much. File
lightlyonlyforremovingburrs.Otherwisetheblade
clearancemaybecometoomuchorthebladelife
may be shortened.
Lower shear blade
1. Applytheroundsurfaceofthediamondletothe
blade edge.
Pushthediamondletowardsthetipofthebladeto
sharpen along the entire blade edge.
Fig.25
2. Applytheatsurfaceofthediamondlelightlyto
theoppositesideoftheblade.
Movethediamondletowardsthetipoftheblade
lightly to remove burrs.
Fig.26
NOTICE: Do not sharpen this side too much. File
lightlyonlyforremovingburrs.Otherwisetheblade
clearancemaybecometoomuchorthebladelife
may be shortened.
Adjustment for blade clearance
Fig.27: 1.Platexingbolt 2.Lockplate
3. Blades tightening nut
Fromtimetotime,adjusttheclearanceoftheshear
bladesasfollows:
1. Switch on the tool, and pull the switch trigger to
open the shear blades.
2. Withshearbladesopen,switchoffthetool.And
disconnecttheconnectioncordfromthetool.
3. Loosentheplatexingbolt.Andthenremovethe
lock plate.
4. Adjustthetightnessofthebladestighteningnut
byhand(fasteningtorqueforthebladetighteningnut:
approximately0.5N•m).
5. Installthelockplateandplatexingboltagain.
6. Checkthetightnessofthebladewhetherthe
blades never rattle but upper blade can be opened or
closedabout3mmbyhand.Ifthebladesaretootightor
loose,adjusttheclearanceagain.
NOTICE:Payattentiontotheclearanceofthe
blades.Toolooseclearancemayresultindullcut,
and too tight blade clearance may result in overload
forthemotorandshortrunningtimeofthetool.
Removing or installing shear blades
Toremovetheshearblades,performfollowingsteps:
1. Tilttheopeningangleselectorlevertotheleftside
rsttoopenthebladesfully.
2. Switch on the tool, and pull the switch trigger to
open the shear blades.
3. Withshearbladesopen,switchoffthetool.And
disconnecttheconnectioncordfromthetool.
Fig.28
4. Remove two bolts near the switch trigger with the
hex wrench.
Remove the trigger guard by separating the tongue on
thetriggerguardfromthegrooveofthehousing.
Fig.29: 1.Bolts 2.Triggerguard
5. Remove the E-ring on the link arm with a slotted
screwdriver or alike.
Fig.30: 1. E-ring 2. Link arm
NOTICE:TheE-ringisexpendablepart.Donot
re-use the E-ring when reassembling.
6. Carefullyremovethepin.
Fig.31: 1. Pin
7. Removetwoboltsfromthesideofthehousing.
Fig.32: 1. Bolts
8. Carefullyremovetheupperandlowershearsfrom
the housing.
Fig.33
9. Toseparatetheupperbladeandthelowerblade,
rstloosentheplatexingbolt.
Thenremovethelockplate.
Fig.34: 1.Platexingbolt 2.Lockplate
10. Loosen and remove the blades tightening nut.
Fig.35: 1. Blade tightening nut 2. Blade tightening
bolt
Toinstalltheshearblades,performtheprocedures
above in reverse. Make sure all the bolts are securely
tightened.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar AR-3733 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar AR-3733 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info