507649
15
Zoom out
Zoom in
Previous page
1/28
Next page
15
Do not work with the chain saw without Þ rst checking
the chain brake!
- Start the engine as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
- Grasp the tubular handle Þ rmly with one hand and hold the
grip with the other.
- With the engine running at moderate speed, press the hand
guard (C/1) in the direction of the arrow with the back of
your hand until the chain brake engages. The chain should
stop immediately.
- Immediately release the throttle and release the chain
brake.
IMPORTANT: If the chain does not stop immediately
when you test the chain brake, do NOT use the chain
saw. Take the chain saw to a DOLMAR service center.
Checking the chain brake
D
C
1
Never work with the chain saw withoute sufÞ cient chain lubri -
ca tion. Otherwise the service life of the chain and guide bar
will be reduced. Before starting work check the oil level in the
tank and the oil feed.
Check the oil feed rate as described below:
- Start the chain saw.
- Hold the running chain saw approx. 15 cm above a trunk
or the ground (use an appropriate base).
If the lubrication is sufÞ cient, you will see a light oil trace be-
cause oil will be ß ung off the sawing device. Pay attention to the
direction the wind is blowing and avoid unnecessary exposure
to the oil spray!
Checking the chain lubrication
E
Adjusting the carburetor
(only for EU-countries)
Carburetor adjustment must only be done with the engine
warm, a clean air Þ lter and the saw chain properly tensioned
and mounted. Always have a DOLMAR service centre do
carburetor adjustment, since incorrect adjustment can
cause considerable damage to the engine.
Due to new emissions regulations, the adjustment range of
screws (H) and (L) has been limited. This adjustment range
limitation (to about 180 degrees) prevents over-rich settings.
This ensures compliance with emissions regulations, optimum
engine performance and economical fuel consumption.
Factory setting of adjustment screws (H) and (L):
Screwed out almost all the way (counter-clockwise).
For proper adjustment, proceed as follows:
Checking adjustment screw (H)
Before starting, make sure that adjustment screw (H) is un-
screwed all the way (until you feel a stop). Limitations do not
protect against too lean running (insufÞ cient fuel)!
1. Start engine and let it warm up (3-5 minutes)
2. Set idle
3. Check acceleration
4. Set highest permissible speed.
5. Check idle speed
2. Set idle
Set the idle speed per the technical speciÞ cations.
Turning the adjusting screw (S) in (clockwise) increases the
idle speed. Turning it out (counter-clockwise) lowers the idle
speed. The chain or blade must not move in idle!
3. Check acceleration
When the throttle is pressed, the engine should go smoothly
from idle to high speed.
Unscrew adjustment screw (L) counter-clockwise in small
steps until acceleration is good.
4. Set the top speed
Set the top speed with a minimal adjustment to screw (H)
in accordance with the technical data.
Screwing in adjustment screw (H) clockwise increases
engine speed. Never exceed the top speed under any
circumstances!
5. Checking the idle speed
After setting the maximum permissible speed, check the idle
speed (the saw chain or cutting tool must not turn in idle).
Repeat the adjustment procedure starting with step 2 above
until idle speed, acceleration, and speed are all good.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar 115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar 115 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar 115

Dolmar 115 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info