766055
8
Zoom out
Zoom in
Previous page
1/15
Next page
8
With your transmitter you can extend and reduce the width of the warning and correcting
zones, depending on conditions in your piece of land and upon how the wire is laid.
a) The warning zone (sound signal)
It is innitely adjustable from 0,40 m to 5 m (the detection distance is approximate, depen-
ding on the loop length and location of the wire) along both sides of the wire using the
knob located on the transmitter panel. Steps 0 to 10 will help you dene the zone width
according to your needs, whereas it approximately holds true that 0 = 0,40 m and 10 = 5 m.
b) The correcting zone (stimulation impulse)
It is innitely adjustable from 0,30 m to 1,50 m (the detection distance is approximate,
depending on the loop length and location of the wire) along both sides of the wire. Steps
0 to 10 will help you dene the one width according to your needs, whereas it approximately
holds true that 0 = 0,30 m and 10 = 1,5 m.
c) Checking and setting the zones
Before you let your dog enter its restricted area, you should physically check the surface and
boundaries of your piece of land assigned to your pet. For this purpose, rst place the leads
of the testing discharge lamp under the contact points of the receiving collar; release them
slightly and then fasten them slightly again so that they can press down the testing lamp
wires. Install a battery in the receiving collar and then power up the transmitter by setting
the switch to the left to ON. Set both potentiometer knobs to ”0“ position.
Correcting zone setting
Select a distance from the antenna wire where you wish to dene the correcting zone for
your dog, stand up on that place and hold the receiving collar by the strap about 30 cm
above ground with the logo facing to the antenna wire.
Then, turn slowly the potentiometer to adjust the correcting zone as long as the test LED is
regularly on in given intervals (approximately after 1 second) along with audible sound
signal.
Warning zone setting
The procedure is the same as the previous one. Select a distance from the antenna wire
where you wish to dene the warning zone for your dog, stand up on that place and hold
the receiving collar by the strap about 30 cm above ground with the logo facing to the
antenna wire. Then, turn slowly the potentiometer to adjust the warning zone as long as a
rapid intermittent sound signal is heard.
Important:
The zone width is changed according to the length and location of the antenna wire
in your piece of land. The longer the antenna wire is, the narrower are the zones.
The width may also be dierent at the bends (in the corners) compared to straight
sections.
Zone width setting (”warning“ and ”correcting“ zones)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dogtrace d-fence at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dogtrace d-fence in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info