766055

Dogtrace d-fence Manual

6
Zoom out
Zoom in
Previous page
1/15
Next page
6
Antenna wire
To make the system work, the wire must be connected to the transmitter and it must form
an uninterrupted wire loop of 0,75 mm2 to 2,5 mm2 cross section, depending on the loop
length. Unreel the wire from the transmitter round your piece of land. To take the wire out of
the garage, your house, or any other covered location where the transmitter is located, pull
it through the window, door or do it in another suitable way. The wire can be laid on the
ground, slightly buried (max. 5 cm deep), or it can be xed to the existing fence or wall (in
this case max. up to 30 cm above the ground). The wire must not be tight or it might get
broken due to changes in temperature.
If you need more than 100 m of the antenna wire, you must extend it with another wire of
necessary length using vampire connectors or in any other suitable and reliable way.
However, the point of connection (nor any other portion of wire) must not be left uninsulated.
With the vampire connectors delivered by us, it is not necessary to remove the insulation
from the end of the wire. If you wish your dog to pass freely across a certain location in your
piece of land where the wire must be led (e.g. between the transmitter located in the garage
and the wire installed round your piece of land), coil the outgoing wire round the incoming
one: the wires twisted round each other result in extinction of emitted waves.
Do not shape the wire at right angles, but make preferably wider curves if possible.
After you have made the loop and you are back with the other end at the transmitter,
remove insulation from both ends of the wire and x them to the transmitter connector
using two screws.
Insert the connector in the appropriate port of the transmitter (the connector is shaped and
it can be inserted in one way only).
Restricting targets (refer to Optional accessories)
They enable your dog to see the zone where it can freely move as well as the boundaries it
may not get over (if the wire is laid across the place where the boundary is not restricted in
a natural way, such as a hedge). It is recommended to place the marks along the internal
edge of the acoustic warning zone, close enough to one another.
As soon as your dog is familiar with its borderline, the marks can be removed.
Before installing your d-fence system, it is useful to make a small sketch of your piece of land
and indicate the layout of your antenna wire, especially its connectors (refer to the diagram).
Antenna wire
By winding the outgoing wire round the incoming one the wave emissions are mutually
suppressed and the animal can freely move within this location.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dogtrace d-fence at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dogtrace d-fence in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info