695365
32
Zoom out
Zoom in
Previous page
1/76
Next page
English
INSTALLATION MANUAL
9.2 Interior lining
9.2.1 Vermiculite
The fire's vermiculite plates are located on the bottom and against the rear wall of the appliance
(see Annex 2, fig. 7). In the following situations the vermiculite plates must be taken out:
- When disassembling the air slide valve (see section 9.1.2).
- To be able to reach the adjustable legs (see section 9.5).
- When replacing the vermiculite plates.
The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the
vermiculite plates takes place in reverse order.
!Caution
Make sure that the vermiculite plates are placed back in the original position! The back plate, for instance, must be
placed with the small, not countersunk, holes towards the front.
9.2.2 Flame baffle plate
On delivery the flame baffle plate (see Annex 2, fig. 7) will be lying on the bottom of the appliance.
It must be placed on the accompanying profiles in the top of the appliance.
To do this proceed as follows:
Ø
Take the flame baffle plate and tilt it backwards.
!Caution
The stainless steel profile must be placed at the front with the screw heads facing the top (see Annex 2, fig. 7).
Ø
Lift the flame baffle plate into the top of the appliance.
Ø
Slide the front of the flame baffle plate over the 2 iron supports located at the top, at the front of the appliance
(see Annex 2, fig. 8).
Ø
Then slide the flame baffle plate towards the back and centre it in the appliance.
Ø
The flame baffle plate is now in the correct place.
The removal of the flame baffle plate takes place in reverse order.
9.3 Door adjustment
Check the closing of the door during installation or maintenance. The door can be adjusted if desired. This will be
the case if sealing is insufficient (gaps).
Ø
Check the sealing of the door by placing a sheet of paper between the door and the fire. After closing the door, it
should not be possible to pull out the sheet of paper easily. Check the outside of the fire.
Proceed as follows when adjusting the door:
Ø
Loosen the 2 hexagonal bolts on the top and bottom side of the non-hinging part of the door with an open-end
spanner by one turn (see Annex 2, fig. 9).
!Caution
Do not fully remove these bolts!
Ø
The door can now be adjusted.
Ø
Check whether the door still seals well, using the test with a sheet of paper described above.
Ø
Tighten the bolts again.
9.4 Glass panes
!Caution
- Avoid damage when removing/fitting the glass pane.
- Avoid/remove fingerprints on the glass pane(s) as they will burn into the glass.
!Tip
Use the supplied glass pane cleaner to remove fingerprints from the glass pane(s).
9.4.1 Disassembly of glass panes
9.4.1.1 Disassembly of glass pane in door
To remove the glass pane in the door, please follow the instructions below (see Annex 2, fig. 10):
Ø
Open the door.
Ø
Lift out the door by sliding it upwards.
Ø
Place the door on a flat surface.
Ø
Remove the door seal.
Ø
Unscrew the nuts under the door seal from the glass strip.
Ø
Remove the glass strips.
Ø
Lift the glass pane out. The pane seal is also taken out.
UK
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Vidar Triple-wall at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Vidar Triple-wall in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Vidar Triple-wall

Dik Geurts Vidar Triple-wall User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info