695335
33
Zoom out
Zoom in
Previous page
1/76
Next page
English
INSTALLATION MANUAL
The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the
vermiculite plates takes place in reverse order.
!Caution
Make sure that the vermiculite plates are replaced in the original position! The back plate with the small, not
countersunk, holes must be placed to the front.
9.2.2 Flame baffle plate
On delivery the flame baffle plate (see Appendix 2, Fig. 8) is laying on the bottom of the appliance. It must be laid
in the top of the appliance.
To do this proceed as follows:
Ø
Take the flame baffle plate and tilt it to the right.
!Caution
The stainless steel profile must be placed at the front with the screw heads facing the top (see Appendix 2, fig. 8).
Ø
Lift the flame baffle plate into the top of the appliance.
Ø
Slide the left-hand side of the flame baffle plate over the edge.
Ø
Now lift the right-hand side up and slide the flame baffle plate to the right, so the right-hand side falls over the
right edge.
Ø
Centre the flame baffle plate as far as possible to the back in the appliance.
Ø
The flame baffle plate is now in the correct place.
9.3 Door adjustment
Check the closing of the door with installation or maintenance. The door can be adjusted if desired. This is the
case if sealing is insufficient is (gaps).
Ø
Check the sealing of the door by placing a sheet of paper between the door and the fire. After closing the door the
sheet of paper may not be able to be easily pulled out. Check around the door.
Proceed as follows when adjusting the door:
Ø
Loosen the 2 hexagonal bolts on the top and bottom side of the hinging part of the door with an open-end
spanner one turn (see Appendix 2, Fig. 9).
!Caution
Do not fully remove these bolts!
Ø
The door can now be adjusted.
Ø
Check whether the door still seals well using the test with a sheet of paper described above.
Ø
Tighten the bolts again.
Does the door still not seal properly?
Ø
Replace the sealing cord (see Appendix 2, Fig. 10).
Ø
Adjust the door handle.
When replacing the cord proceed as follows:
Ø
Open the door.
Ø
Remove the cord and the mastic from the recess.
Ø
Apply a new layer of high temperature-resistant mastic in the recess where the cord was.
Ø
Place a new cord in the recess. Do this loosely and do not pull the cord tight.
Ø
Insert both ends of the cord in the special sleeve.
The cord, the sleeve and the mastic are available through your supplier.
!Caution
Make sure that the sleeve is placed on the underside of the glass pane.
The door can also be adjusted in height. There are 2 eyelets on the upper pin on which the door is hung.
Removing one or more of these eyelets allows the door to fall to the desired level.
Proceed as follows when adjusting the door handle:
Ø
Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 11).
This pin ensures that the door is tightly clamped.
Ø
Adjust the pin.
Ø
Tighten the 2 hexagonal nuts again.
Ø
Test the sealing of the door (see the start of this paragraph).
Ø
Repeat this process if the result is not satisfactory.
UK
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Prostyle 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Prostyle 600 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Prostyle 600

Dik Geurts Prostyle 600 User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info