695335

Dik Geurts Prostyle 600 Manual

32
Zoom out
Zoom in
Previous page
1/76
Next page
English
INSTALLATION MANUAL
9.1.3 Connection of the flue
In an existing situation the flue can be connected in three ways: without venting material, using a fixed
connection or by using a flexible connection.
!CAUTION
Not all connection methods are allowed in all countries! Install the appliance strictly according to the
country-specific conditions.
For the method without venting material you must create an airtight connection with ceramic wool between
the top side of the fire and the chimney (see paragraph 5.4.2).
When making a fixed connection use must be made of the specially developed tapered ring or the draining
flex/fix connecting piece. This is available through your supplier.
Proceed as follows (see Appendix 2, Fig. 6a to 6c):
Ø
Fix the ring/connecting piece using three bolts on the top side of the appliance.
Ø
Fit the appliance.
Ø
Slide the pipe over the tapered ring or into the draining flex/fix connecting piece.
A draining flex/fix connecting piece is available for a flexible connection.
Proceed as follows (see Appendix 2, Fig. 6a to 6c):
Ø
Pull the flexible pipe through the chimney.
Ø
Fix the draining flex/fix connecting piece using 3 self-tapping screws to the flexible pipe.
Ø
Push the flexible pipe including connecting piece back in the chimney.
Ø
Slide the fire into place.
Ø
Remove the flame baffle plate if this is already in the correct place in the top of the appliance (see paragraph
9.2.2).
Ø
Insert a hand through the flue hole and grasp the connecting piece handle.
Ø
Pull the flexible pipe with the connecting piece downwards.
Ø
Fasten the flexible connecting piece to the appliance with three bolts.
!Caution
The handle in the flexible connecting piece (see Appendix 2, Fig. 6b) can be broken out after installation. This is
not necessary but can be desirable for sweeping the chimney.
Tip!
The draining flex/fix connecting piece can be used to make both a flexible or fixed connection.
!Caution
With a fixed connection the pipe material lowers fully into the connecting piece, with a flexible connection only
half of it (see Appendix 2, Fig. 6c).
9.1.4 Air slide valve
With installation and maintenance of the appliance check the operation of the air slide valve (see Appendix 2, Fig.
7). There is the possibility that steel grit entered the air slide valve during transport. If the air slide valve does not
move smoothly it must be cleaned. The air slide valve must be disassembled to do this. The air slide valve is
suspended sprung by means of a bolt and a spring located below the cover plate.
Proceed as follows when disassembling the air slide valve (see Appendix 2, Fig. 7):
Ø
Remove the vermiculite plates and the felt from the bottom (see section 9.2.1).
Ø
Remove the 5 cover plate socket screws from the bottom.
Ø
Remove the cover plate.
Ø
If there is an outside air connection remove the 2 screws from the front strip.
!Caution
You only have to remove the front strip if an exterior connection is assembled.
Ø
Remove the socket screw with spring (see Annex 2, fig. …(..)).
Ø
Remove the air slide valve by bringing it towards you.
Ø
Check the air slide valve and clean it if necessary.
To replace the air slide valve proceed as described for removal in reverse order.
9.2 Interior lining
9.2.1 Vermiculite
The fire’s vermiculite plates are located on the bottom against the rear wall and/or side walls of the appliance. In
the following situations the vermiculite plates must be taken out:
- When disassembling the air slide valve (see section 9.1.4).
- To be able to reach the adjustable legs (see section 9.6).
- When replacing the vermiculite plates.
UK
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Prostyle 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Prostyle 600 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Prostyle 600

Dik Geurts Prostyle 600 User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info