712289

DeWalt DCMW564 Manual

43
Zoom out
Zoom in
Previous page
1/184
Next page
41
ENGLISH
4. Install sharpened or new blade
29
on shoulder
31
of the
blade fan
30
as shown in Fig. P.
NOTE: When replacing sharpened or new blade on shoulder
31
of blade fan
30
, make sure the “GRASS SIDE” on the blade will
be facing the ground when the mower is returned to its normal
upright position.
5. Install the plastic blade insulator
28
on the blade such that
the raised lips on one side engage the edges of the blade.
6. Install the blade spacer
27
so that it sits inside the raised
lips on the other side of the blade insulator. Be sure to align
the flats in the hole of the blade spacer with the flats of
the shaft, rotating the blade and blade insulator together
asnecessary.
7. Position piece of wood
24
to keep blade from turning
as shown in Fig. Q. Install flange nut
25
with the flange
against the blade spacer
27
and securely tighten with
awrench.
Blade Sharpening
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL
BLADE DOES NOT CUT GRASSCLEANLY.
• DCMW564 requires replacement blade DT20671.
The use of accessories not recommended in this manual
may be hazardous.
WARNING: Use gloves and proper eye protection while
removing, sharpening, and installing blade. Ensure that
safety key and battery packs are removed.
Sharpening the blade twice during a mowing season is usually
sufficient under normal circumstances. Sand causes the blade
to dull quickly. If your lawn has sandy soil, more frequent
sharpening may berequired. REPLACE BENT OR DAMAGED
BLADEIMMEDIATELY.
When Sharpening the Blade
• Make sure blade remainsbalanced.
• Sharpen blade at the original cuttingangle.
• Sharpen cutting edges on both ends of blade, removing
equal amounts of material from bothends.
To Sharpen Blade in a Vice (Fig. R)
1. Be sure the bail handle is released, the blade has stopped
and safety key and battery packs are removed before
removing theblade.
2. Remove blade from mower. See instructions for Removing
and InstallingBlade.
3. Secure blade
29
in a vice
32
.
4. Wear proper eye protection and gloves and be careful not
to cutyourself.
5. Carefully file the cutting edges of the blade with a fine-tooth
file
33
or sharpening stone, maintaining the angle of the
original cuttingedge.
6. Check balance of blade. See instructions for
BladeBalancing.
7. Replace blade on mower and tightensecurely.
Blade Balancing (Fig. S)
Check balance of the blade
29
by placing centre hole in the
blade over a nail or round screwdriver
34
, clamped horizontally
in a vice
32
. If either end of the blade rotates downward, file
along the sharp edge of that dropping end. Blade is properly
balanced when neither enddrops.
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require nolubrication.
Cleaning
Release bail handle
5
to turn mower off, let the blade come
to a stop and then remove safety key. Clean out any clippings
which may have accumulated on the underside of the deck.
After several uses, check all exposed fasteners fortightness.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Preventing Corrosion
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilizers or chemicals have been used, the mower
should be cleaned immediately afterward as follows: Release
bail handle
5
to turn mower off and unplug safety key. Wipe all
exposed parts with a dampcloth.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCMW564 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCMW564 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 21,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info