790944

DeWalt DCE080GS Manual

20
Zoom out
Zoom in
Previous page
1/232
Next page
20
GB 4. On the top of the display window, view the Accuracy Mode icon
(Figure F 8).
• indicates that the detector will give an “on grade” reading
only when the laser beam is on grade or no more than 1mm
(1/25") above or below it.
• To change the Accuracy Mode to to have the detector
give an “on grade” reading when the laser beam is on grade
or approximately 3mm (1/8") above or below it, press the
Accuracy Mode button (Figure F 3) once. Then (Figure
F 9) appears on the display window.
5. Position the detector so that the detector window (Figure F 14 )
is facing the laser beam produced by the rotary laser (Figure G).
Move the detector up or down within the approximate area of the
beam, until you have centered the detector.
6. Use the marking notches (Figure F 7) to accurately mark the
position of the laser beam.
7. To turn the detector off.
• On the detector, press for 3 seconds.
• If a rotary laser beam does not strike the detector's beam
detection window, or if no detector buttons are pressed, within
30 minutes, the detector will shut itself off.
Controlling the Laser Remotely
You can control the laser unit remotely in either of these 3 ways:
• From up to 15m away, you can use the remote to control the
laser unit (Figure I 1). IR sensors will maintain communication
between the remote and the laser unit.
• From up to 30m away, you can use the DEWALT® Tool Connect™
Application on your Bluetooth® device to connect to the laser unit
(Figure I 2).
• From up to 335m away, you can control the laser unit by using
the DEWALT® Tool Connect™ Application on your Bluetooth®
device to connect to the detector that is connected to the laser unit
(Figure I 3). You must press the Detector button (Figure A
6) on the laser in order to connect the detector to the laser unit.
Controlling the Laser from up to 15m Away
The DCE080RS/GS remote control allows you to operate and set
up the laser from up to 15m away. The LED light on the remote
control (Figure B 1) indicates a signal is being transmitted from the
DCE080RS/GS laser unit.
You can use all the buttons on the remote's keypad to control the
laser unit. To completely power OFF a DCE080RS/GS laser unit
using the Remote keypad, press the X-Y axis button (Figure
B 5) and the Slope Mode button (Figure B 2) simultaneously.
By default, the laser unit is not paired to a remote (the laser unit is
in Public mode). LEDs on the laser unit and the remote will indicate
that they are not paired.
UNLOCKED
in Public Mode
LOCKED
in Private Mode
Description A laser is in Public Mode
if it is not paired with a
remote.
A laser is in Private
Mode if it is paired
with a remote.
A remote is in Public
Mode if it is not paired
with a laser.
A remote is in Private
Mode if it is paired
with a laser.
Control A Public laser can be
controlled by more
than one Public remote
(Figure K 1).
A Private laser can only
be controlled by the
remote to which it is
paired (Figure L).
A Public remote can
control more than one
Public laser (Figure
K 2).
A Private remote can
only control the laser
to which it is paired
(Figure L).
LEDs The unlocked LED
will be lit on the laser
keypad (Figure K 1 and
K 2 ).
The locked LED
on the laser will be lit
(Figure L).
The locked LED on the
remote will NOT be lit
(Figure K 1 and K 2 ).
The locked LED on
the remote WILL be lit
(Figure L).
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE080GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE080GS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info