790944

DeWalt DCE080GS Manual

19
Zoom out
Zoom in
Previous page
1/232
Next page
19
GB
4. If you want to use the laser in plumb (vertical) mode, carefully
turn the laser so the keypad is at the top (Figure H 2). The
Dot rotates down to 6 o’clock. Press to make sure the laser
rotates.
5. Adjust the rotation speed and controls, as desired (Figure P).
NOTE:
The laser will be easier to set up for wall applications if the
rotation speed is set to 0RPMs and the remote control is used
to line up the laser with control marks. The remote allows one
person to set up the laser.
Using the Laser With a Laser Detector
How the Detector works
Some laser kits include a DeWALT Digital Laser Detector. The
DeWALT Digital Laser Detector allows you to locate a laser beam
emitted by a rotary laser in bright light conditions or over long
distances.
• The detector can be used in both indoor and outdoor situations
where it is difficult to see the laser beam.
• The detector is not for use with non-rotating lasers but is
compatible with most rotary red-beam (DCE080RS) and green
beam (DCE080GS) lasers.
• The detector can be set to indicate the location of the beam to
either the nearest 2mm (5/64") or the nearest 1mm (3/64").
• The detector gives both visual signals through the display window
(Figure F 6) and audio signals through the speaker (Figure
F 5) to indicate the location of the laser beam.
Detector’s Indicators
Above
Grade
Slightly
Above
Grade
On
Grade
Slightly
Below
Grade
Below
Grade
Audible
Signal
Fast Beep Fast Beep Steady
Tone
Slow Beep Slow Beep
Display
Icon
• The DEWALT Digital Laser Detector can be used with or without
the detector clamp. When used with the clamp, the detector can be
positioned on a grade rod, leveling pole, stud, or post (Figure G).
To connect the detector to the clamp:
• Push in the clamp latch (Figure G 3).
• Slide the tracks on the clamp (Figure G 4) around the rail on
the back of the detector (Figure F 11 ) until the button (Figure
G 5) on the clamp snaps into the latch hole on the back of
the detector (Figure F 12 ).
• Turn the clamp knob (Figure G 6) counterclockwise to open
the jaws on the clamp.
• Place the clamp on the rod (Figure G 2) so that the detector
is positioned at the height needed to work with the laser.
• Turn the clamp knob (Figure G 6) clockwise to secure the
clamp on the rod.
Using the Detector
1. Set up and position the rotary laser that you will be using
according to the manufacturer’s directions. Turn the laser on and
make sure the laser is rotating and emitting a laser beam.
2. Press the power button once on the detector to turn the detector
on.
3. On the bottom of the display window, notice the speaker icon
(Figure F 10 ).
• To decrease the volume of the audible signal, press the volume
button (Figure F 4); both half circles next to the speaker icon
(Figure F 10 ) will dissappear.
• To turn off the audible signal, press the volume button (Figure
F 4) until the speaker icon dissapears from the display
window.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE080GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE080GS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info