790944

DeWalt DCE080GS Manual

17
Zoom out
Zoom in
Previous page
1/232
Next page
17
GB
Level Calibration Check (X-axis)
1. Position a tripod securely on the floor between two walls that are
at least 15m apart. The exact location of the tripod is not critical.
2. Make sure that the top of the tripod is roughly level.
• The laser will self-level only if the top of the tripod is within ±
5˚ of level.
• If the laser is set up too far out of level, it will beep when it
reaches the limit of its leveling range. No damage will be done
to the laser, but it will not operate in an “out of level” condition.
3. Attach a tripod adapter (Figure G 1) to the laser unit. The
adapter may be assembled to the bottom for level mode or to
the side for plumb mode.
4. Place the laser with the attached adapter on the tripod and
screw the threaded knob on the tripod into the female thread on
the tripod adapter.
5. Position the laser unit with the tripod so that the laser’s X-axis
points directly toward one of the walls (Figure L 1).
6. Turn the laser unit on and allow it to self-level.
7. Where the beam appears on the left wall, mark point A, and
where the beam appears on the right wall mark point B.
8. Turn the laser unit 180º so that the X-axis points directly toward
the opposite wall (Figure L 2).
9. Allow the laser unit to self-level.
10. Where the beam appears on the left wall, mark point AA, and
where the beam appears on the right wall mark point BB.
11. Calculate the Total Error using the following equation:
Total Error = (AA-A) - (BB-B)
12. If your Total Error measurement is greater than the Allowable
Error for the corresponding Distance Between Walls in the
following table, the laser must be serviced at an authorized
service center.
L (Distance Between
Walls)
Allowable Error
15m (40′) 1.5mm (3/64”)
20m (50′) 2mm (1/16”)
25m (70′) 2.5mm (3/32”)
30m (100’) 3mm (1/8”)
Level Calibration Check (Y-axis)
1. Set up a tripod between two walls that are at least 15m apart.
The exact location of the tripod is not critical.
2. Make sure that the top of the tripod is roughly level.
• The laser will self-level only if the top of the tripod is within ±
5˚ of level.
• If the laser is set up too far out of level, it will beep when it
reaches the limit of its leveling range. No damage will be done
to the laser, but it will not operate in an “out of level” condition.
3. Attach a tripod adapter (Figure G 1) to the laser unit. The
adapter may be assembled to the bottom for level mode or to
the side for plumb mode.
4. Place the laser with the attached adapter on the tripod and
screw the threaded knob on the tripod into the female thread on
the tripod adapter.
5. Position the laser unit with the tripod so that the laser’s Y-axis
points directly toward one of the walls (Figure M 1).
6. Turn the laser unit on and allow it to self-level.
7. Where the beam appears on the left wall, mark point A, and
where the beam appears on the right wall mark point B.
8. Turn the laser unit 180º so that the Y-axis points directly toward
the opposite wall (Figure M 2).
9. Allow the laser unit to self-level.
10. Where the beam appears on the left wall, mark point AA, and
where the beam appears on the right wall mark point BB.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE080GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE080GS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info