790944

DeWalt DCE080GS Manual

18
Zoom out
Zoom in
Previous page
1/232
Next page
18
GB 11. Calculate the Total Error using the following equation:
Total Error = (AA-A) - (BB-B)
12. If your Total Error measurement is greater than the Allowable
Error for the corresponding Distance Between Walls in the
following table, the laser must be serviced at an authorized
service center.
L (Distance Between Walls) Allowable Error
15m (40′) 1.5mm (3/64”)
20m (50′) 2mm (1/16”)
25m (70′) 2.5mm (3/32”)
30m (100’) 3mm (1/8”)
Plumb Error Check
Perform this check using a wall that is no shorter than the tallest wall
for which this rotary laser will be used (Figure N).
1. Using a standard plumb bob as a reference, mark the top and
bottom of a wall. (Be sure to mark the wall and not the oor or
ceiling).
2. Position the rotary laser securely on the oor approximately 1m
(3”) from the wall.
3. Turn the laser on and point the laser dot at the mark on the
bottom of the wall.
4. Using the or arrow on the Remote Control (Figure B 6 or
7), rotate the dot upwards.
5. If the center of the dot scans over the mark on the top of the
wall, the laser is properly calibrated.
Using the Laser
Using the Laser on a Tripod
1. Position a tripod securely and set it to the desired height. Make
sure that the tripod has a 5/8”-11 threaded screw to ensure
secure mounting of the laser unit.
2. Make sure that the top of the tripod is roughly level.
• The laser will self-level only if the top of the tripod is within ±
5˚ of level.
• If the laser is set up too far out of level, it will beep when it
reaches the limit of its leveling range. No damage will be done
to the laser, but it will not operate in an “out of level” condition.
3. Attach a tripod adapter (Figure G 1) to the bottom of the laser
unit (Figure G 2).
4. Place the laser with the attached adapter on the tripod and
screw the threaded knob on the tripod into the female thread on
the tripod adapter.
5. Turn the laser ON and allow it to self-level in horizontal (level)
mode (Figure H 1).
6. If you want to use the laser in vertical (plumb) mode, follow
these steps while the laser is still ON:
• Carefully remove the laser unit from the tripod.
• Remove the tripod adapter (Figure I 1) from the bottom of
the laser unit (Figure I 2) and attach it to the side (Figure
I 3).
• With the laser in the vertical (plumb) position, attach the laser
unit to the tripod (Figure I 4). The Dot rotates down to 6
o’clock.
• Press to make sure the laser rotates.
7. Adjust the rotation speed and controls, as desired (Figure P).
Using the Laser on a Floor
The laser level can be positioned directly on the floor for leveling and
plumbing applications such as framing walls.
1. Place the laser on a relatively smooth and level surface where it
will not be disturbed or exposed to vibration.
2. Position the laser for a level setting (Figure H 1).
3. Turn the laser ON and allow it to self-level in horizontal (level)
mode (Figure H 1).
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCE080GS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCE080GS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info