391299
39
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
37
After approx. 1 hour all three indicators will remain
constant.
Charging process (fi g. 2)
Refer the table below for the state of charge of the
battery pack.
State of charge
1 light blinking < 33%
1 light blinking, 1 light on 33-66%
1 light blinking, 2 lights on 66-99%
3 lights on 100%
Automatic refresh
The automatic refresh mode will equalise or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed weekly
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery in the
charger as usual. Leave the battery pack for at least
8 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
DEEP DISCHARGE PROTECTION
The battery pack is protected against deep
discharging when it is used in the tool.
Inserting and removing the
battery pack into the tool (fi g. 2)
WARNING: To reduce the risk
of serious personal injury, make
certain the lock-off button (b)
is engaged to prevent switch
actuation before removing or
installing battery.
1. To fit the battery pack (i), line it up with the
receptacle on the tool. Slide the battery pack
into the receptacle and push until the battery
snaps into place.
2. To remove the battery pack, push the battery
release button (j) while at the same time pulling
the battery pack out of the receptacle.
ASSEMBLY AND ADJUSTMENTS
Attaching Side Handle
The side handle (d) can be fitted to either side of the
gear case in the threaded holes. Before using the
tool, check that the handle is tightened se cure ly.
To improve user comfort, the gear case will rotate
90˚ for cutting operations.
Rotating the Gear Case (fi g. 3)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
1. Remove the four corner screws attaching the
gear case to motor housing.
2. Without separating the gear case from motor
housing, rotate the gear case head to desired
position.
NOTE: If the gear case and motor housing become
separated by more than 6.35 mm (1/4"), the tool
must be serviced and re-assembled by a DEWALT
service center. Failure to have the tool serviced may
cause brush, motor and bearing failure.
3. Re-install screws to attach the gear case to
the motor housing. Tighten screws to 2.08 Nm
(18 in-lbs.) torque. Overtightening could cause
screws to strip.
Mounting Guard
MOUNTING AND REMOVING GUARD (FIG. 4)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
CAUTION: Guards must be used
with all grinding wheels, cutting
wheels, sanding flap discs, wire
brushes, and wire wheels. The tool
may be used without a guard only
when sanding with conventional
sanding discs. The DC413/DC415 is
provided with a guard intended for use
with depressed center wheels (Type 27)
and hubbed grinding wheels (Type 27).
The same guard is designed for use
with sanding flap discs (Type 27 and 29)
and wire cup brushes.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc 415 kl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc 415 kl in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info