391299

DeWalt dc 415 kl Manual

41
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
39
2. Depress the spindle lock button and use a
wrench to tighten the hub of the wheel.
3. Reverse the above procedure to remove the
wheel.
CAUTION: Failure to properly seat
the wheel before turning the tool on
may result in damage to the tool or the
wheel.
MOUNTING NON-HUBBED WHEELS (FIG. 7)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
Depressed center Type 27 grinding wheels must be
used with included flanges.
1. Install the anti-lockup backing flange (f) on
spindle (r) with the raised centre against the
wheel. Be sure the backing flange recess is
seated onto the flats of the spindle by pushing
and twisting the flange before placing the
wheel (s).
2. Place wheel against the backing flange,
centering the wheel on the raised centre of the
backing flange.
3. While depressing the spindle lock button, thread
the clamp nut (g) on spindle. If the wheel you
are installing is more than 3.17 mm (1/8") thick,
place the threaded clamp nut on the spindle so
that the raised centre fits into the center of the
wheel (Fig. 7A). If the wheel you are installing is
3.17 mm (1/8") thick or less, place the threaded
clamp nut on the spindle so that the raised
centre is not against the wheel (Fig. 7B).
4. While depressing the spindle lock button,
tighten the clamp nut with a wrench.
5. To remove the wheel, depress the spindle lock
button and loosen the threaded clamp nut with
a wrench.
NOTE: If the wheel spins after the clamp nut is
tightened, check the orientation of the threaded
clamp nut. If a thin wheel is installed with the pilot on
the clamp nut against the wheel, it will spin because
the height of the pilot prevents the clamp nut from
holding the wheel.
SURFACE GRINDING WITH GRINDING WHEELS
1. Allow the tool to reach full speed before
touching the tool to the work surface.
2. Apply minimum pressure to the work surface,
allowing the tool to operate at high speed.
Grinding rate is greatest when the tool operates
at high speed.
3. Maintain a 20˚ to 30˚ angle between the
tool and work surface.
4. Continuously move the tool in a forward and
back motion to avoid creating gouges in the
work surface.
5. Remove the tool from work surface before
turning tool off. Allow the tool to stop rotating
before laying it down.
EDGE GRINDING WITH GRINDING WHEELS
WARNING: Wheels used for cutting
and edge grinding may break or kick
back if they bend or twist while the tool
is being used to do cut-off work or deep
grinding. To reduce the risk of serious
injury, limit the use of these wheels with
a standard Type 27 guard to shallow
cutting and notching [less than 13 mm
(1/2") in depth]. The open side of the
guard must be positioned away from
the operator. For deeper cutting with
a Type 1 cut-off wheel, use a closed
Type 1 guard.
1. Allow the tool to reach full speed before
touching the tool to the work surface.
2. Apply minimum pressure to the work surface,
allowing the tool to operate at high speed.
Grinding rate is greatest when the tool operates
at high speed.
3. Position yourself so that the open-underside of
the wheel is facing away from you.
4. Once a cut is begun and a notch is established
in the workpiece, do not change the angle of
the cut. Changing the angle will cause the wheel
to bend and may cause wheel breakage. Edge
grinding wheels are not designed to withstand
side pressures caused by bending.
5. Remove the tool from the work surface before
turning the tool off. Allow the tool to stop
rotating before laying it down.
WARNING: Do not use edge grinding/
cutting wheels for surface grinding
applications because these wheels
are not designed for side pressures
encountered with surface grinding.
Wheel breakage and serious personal
injury may result.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc 415 kl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc 415 kl in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info