391299

DeWalt dc 415 kl Manual

40
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
38
1. Open the guard latch (n), and align the lugs (p)
on the guard with the slots (o) on the gear case.
2. Push the guard down until the guard lugs
engage and rotate freely in the groove on the
gear case hub.
3. With the guard latch open, rotate the guard (h)
into the desired working position. The guard
body should be positioned between the spindle
and the operator to provide maximum operator
protection.
4. Close the guard latch to secure the guard on
the gear case. You should not be able to rotate
the guard by hand when the latch is closed. Do
not operate the grinder with a loose guard or
the clamp lever in open position.
5. To remove the guard, open the guard latch,
rotate the guard so that the lugs are aligned
with the slots and pull up on the guard.
NOTE: The guard is pre-adjusted to the diameter of
the gear case hub at the factory. If, after a period of
time, the guard becomes loose, tighten the adjusting
screw (q) with clamp lever in the closed position with
guard installed on the tool.
CAUTION: If the guard cannot be
tightened by the adjusting clamp, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
CAUTION: To reduce the risk of
damage to the tool, do not tighten the
adjusting screw with the clamp lever
in the open position. Undetectable
damage to the guard or the mounting
hub may result.
NOTE: Edge grinding and cutting can be performed
with Type 27 wheels designed and specified for this
purpose; 6.35 mm (1/4") thick wheels are designed
for surface grinding while 3.17 mm (1/8") wheels are
designed for edge grinding.
OPERATION
Switch
LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 5)
Your cut-off tool is equipped with a lock-off button (b).
To lock the trigger switch, press the lock-off button
as shown. When the lock-off button is depressed to
the lock icon, the unit is locked.
Always lock the trigger switch when carrying or
storing the tool to eliminate unintentional starting.
To unlock the trigger switch, press the lock-off
button. When the lock-off button is depressed to the
unlock icon, the unit is unlocked. The lock-off button
is colored red to indicate when the switch is in its
unlocked position.
Pull the trigger switch (a) to turn the tool ON.
Releasing the trigger switch turns the tool OFF.
NOTE: This tool has no provision to lock the switch in
the ON position, and should never be locked ON by
any other means.
CAUTION: Hold the side handle and
body of the tool firmly to maintain
control of the tool at start up and during
use and until the wheel or accessory
stops rotating. Make sure the wheel has
come to a complete stop be fore laying
the tool down.
CAUTION: Allow the tool to reach full
speed before touching tool to the work
surface. Lift the tool from the work
surface before turning the tool off.
SPINDLE LOCK
The spindle lock pin is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock pin only when the
tool is turned off, the battery is removed, and the
wheel has come to a complete stop.
CAUTION: To reduce the risk of
damage to the tool, do not engage the
spindle lock while the tool is operating.
Damage to the tool will result and
attached accessory may spin off
possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Mounting and Using Depressed
Center Grinding Wheels and
Sanding Flap Discs
MOUNTING AND REMOVING HUBBED WHEELS (FIG. 6)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
remove battery pack before making
any adjustments or removing/installing
attachments or accessories.
Hubbed wheels install directly on the M14 threaded
spindle.
1. Thread the wheel on the spindle by hand.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc 415 kl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc 415 kl in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info