Manual Crivit CT 5833 IAN 310717 (page 12 of 46) (English, German, Dutch, French, Polish)

735882

Zoom out

Zoom in

1/46

Note: You can attach the pedals to one of the

three positions provided for this purpose. Make

sure that both pedals are attached at the same

position.

Step 3 (Fig. F)

1. Remove the pre-mounted screws, the

washers and the lock washers from the base

frame.

2. Slide the handlebar column cover (13) onto

the handlebars (2).

3. Hold the handlebar column on the base

frame and connect the sensor cables (1c)

and (2a) together.

Note: Make sure that the cables are ﬁrmly

connected so as to ensure reliable signal

transmission.

4. Slide the handlebar column into the base

frame.

Note: Make sure that the cables are not

trapped in the process.

5. Secure the handlebar column with the

previously removed screws using the

combination tool (30).

6. Slide the handlebar column cover over the

screws to cover them.

Step 4 (Fig. G)

Note: Take note of the “R” (right) and “L” (left)

markings.

1. Guide the swivel arm axis (7) through the

axis guide (2b).

2. Firstly attach a lock washer (25) and then

the right swivel arm (3R) to the right side of

the swivel arm axis and secure the arm with

the lock washer (27), the washer (26), and

the screw (24) using the Allen key (29).

3. Next attach a lock washer (25) and then

the left swivel arm (3L) to the left side of the

swivel arm axis and secure the arm with the

lock washer (27), the washer (26), and the

screw (24) using the Allen key (29).

Step 5 (Fig. H)

1. Insert the locking tube on the right pedal bar

(1a) into the right swivel arm (3R). Secure

the tube with the locking screw (3a).

2. Insert the locking tube on the left pedal bar

(1b) into the left swivel arm (3L). Secure the

tube with the locking screw (3a).

Step 6 (Fig. I)

Note: Take note of the “R” (right) and “L” (left)

markings.

1. Attach the right swivel arm handle (4R) onto

the right swivel arm (3R) and secure the

handle with the screws (17) and the washers

(16).

2. Attach the left swivel arm handle (4L) onto

the left swivel arm (3L) and secure the

handle with the screws (17) and the washers

(16).

Step 7 (Fig. J)

1. Remove the pre-mounted screws, the

washers and the lock washers from the

handlebar column.

2. Pass the two heart-rate cables (5a) of the

handholds through the opening (2c) on the

handlebar column. The heart-rate cables

must protrude out the top of the handlebar

column.

3. Secure the handhold (5) with the previously

removed screws using the combination tool

(29).

Step 8 (Fig. K)

1. Hold the computer (11) on the handlebar

column and connect the sensor cable (2d)

from the handlebars to the sensor cable

(11a) from the computer. Connect the two

heart-rate cables (5a) from the handhold

with the two heart-rate cables (11b) from the

computer.

Note: Make sure that the cables are ﬁrmly

connected so as to ensure reliable signal

transmission.

2. Remove the screws from the back of the

computer (11) and fasten the computer to

the handlebar column with these screws.

Note: Make sure that the cables are not

trapped when fastening the computer.

Step 9 (Fig. L)

1. Remove the screws from the swivel arm

covers (12R) (12L) and put the swivel arm

covers on the respective swivel arm.

2. Secure each swivel arm cover with the

previously removed screws.

Step 10 (Fig. M)

1. Remove the screws from the handhold cover

(14).

2. Put the front part of the handhold cover (14)

on the handlebar column and fasten the

handhold cover with the previously removed

screw.

3. Put the rear part of the handhold cover (14)

on the handlebar column and fasten the

handhold cover with the previously removed

screws. Use a standard Phillips screwdriver,

size PH1 (not included).

Step 11 (Fig. N)

1. Remove the pre-mounted screws from the

handlebar column (2).

2. Fix the water bottle holder (15) to the

handlebar column with the previously

removed screws.

Note: Use of the water bottle holder is

optional.

Disassembly

Proceed in the reverse order to disassemble the

item.

Use

• Choose an exercise area of approx.

3.00 x 1.80m (L x W).

• Train on a ﬂat and non-slip surface only.

Turning the item on and oﬀ (Fig. O)

1. Connect the power cable (10) to the item

and to a power point in order to connect the

item to the mains.

2. Press the switch (1d) to turn the item on.

3. Once you have ﬁnished exercising, press the

switch to turn the item oﬀ.

Getting on correctly

1. Hold on to the handhold ﬁrmly with both

hands and at ﬁrst get on with just one leg

onto either the right or left pedal.

2. Put the second leg on the free pedal.

3. Do not reach for the swivel arm handles until

both feet are standing on the pedals.

4. Proceed in the reverse order when you are

getting oﬀ.

Assuming the correct posture

1. Stand on the pedals with the front part of

your feet all the way to the front and assume

an upright body posture.

2. Hold the swivel arm handles with your

hands. There must be a right angle between

your upper and lower arm when your arms

are pulled back.

Note: Keep your arms and legs slightly bent

while exercising.

Note: Wear gym shoes while exercising.

Adjusting the length of the swivel

arm

1. To set the swivel arms to the correct length,

ﬁrstly loosen the locking screw (3a) on the

respective swivel arm (3R) (3L). Then move

the respective locking screw forwards and

push the locking tube of the right or left

pedal bar (1a) (1b) into the desired position

(Fig. H).

2. Release the respective locking screw. The

locking button on the swivel arm must click

into place.

3. Fasten the locking button by tightening the

locking screw.

USB connection

The computer has a USB connection for

connecting your smartphone or tablet.

• To connect your smartphone or tablet,

connect a USB cable (not included) to the

USB connection on the computer and to

your smartphone or tablet.

Using the smartphone or tablet

holder (Fig. P)

1. Place your smartphone or tablet on the

smartphone or tablet holder.

2. Attach your smartphone or tablet with the

clip (11c).

Operating the computer

WARNING! The individual human

performance required to perform an exercise

may differ from the indicated mechanical

performance.

Display (Fig. C)

The following information and functions are

shown on the display:

• Depending on the display status, the heart

rate from 40 to 220 beats per minute or

BMR, body fat and BMI measurements are

displayed (11l).

• Depending on the display status, BMI, body

fat, sex, height, weight or age are displayed

(11m).

• A training duration with pause mode of

between 00:00 and 99:59 is displayed

(11n).

• Resistance with 32 resistance levels is

displayed (11o).

• A pedalling rate of 0 to 999 rotations per

minute is displayed alternately with the

current speed of between 0.0 to 99.9km/hr

(11p).

• The distance pedalled, from 0.0 to 99.9km

is displayed (11q).

GB/IE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit CT 5833 IAN 310717 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit CT 5833 IAN 310717 Manual

Product: