634449
7
Zoom out
Zoom in
Previous page
1/10
Next page
L
Never try to fo
rce the splitting of the log by maintaining
the pressure for several seconds. This can lead to damage to
the machine.
Reposition the log on the main frame and repeat the splitting
process, or put the log to one side.
How to release a jammed log?
1. Loos
e the operating lever as well as the operating
pushbutton that the log ram can go back.
1. Place a triangular wooden chock under the log, then move
the log ram forward so that it pushes the chock under the
jammed log.
2. If the log is not released, keep repeating this procedure,
using larger chocks, until the log is released.
Never use a hammer to release a jammed log, and keep
your hands away from the log.
Do not enlist the aid of a second person - this is a one-man
job.
Do not try to release the log by using a hammer, since this
may break the motor block.
Finishing work:
Wait for the log ram has go back to its initial
starting / basic position.
Then remove the plug from the power socket.
Close the bleed screw. Fig. 5
Follow the care and maintenance instructions.
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remo
ve the plug from the power socket before
starting any maintenance or cleaning work.
Wear protecti
ve gloves in order to avoid injury to the
hands.
L
Observ
e the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have finished
usi
ng it.
Remove any resin remains on the machine.
Oil the piston rod (Fig. 1) regularly with an
environmentally friendly spray oil.
Check the oil level and change the oil as necessary.
Sharpening the splitting wedge
After ex
tended periods of use, or if the splitting performance is
reduced, sharpen the splitting wedge with a file (and remove
any burrs). Fig. 8
Fig. 8
How do I check the oil level?
1. The log r
am must be in its starting position.
2. Stand the log splitter on end, with the filler opening at the
top. Fig
9
A second pe
rson will be required to up-end and
hold the log splitter.
3. Unscrew the dipstick – Fig. 10. Do not drop or lose the oil
seal when removing the dipsti
ck.
4. Clean the dipstick and the oil seal.
5. Replace the dipstick fully into the oil reservoir.
6. Now remove the dipstick again, and read off the oil level.
If the oil
level is between the two marking on the
dipstick, there is sufficient oil in the reservoir.
If the oi
l level is below the lower marking, more oil
should be added with the aid of a clean funnel.
lower marking upper marking
7. Check th
e oil seal and replace it if it is damaged in any
way.
8. Repl
ace the dipstick and screw it firmly into place.
Caution! Do not tighten the screw too tightly, since this may
damage the oil seal or the thread in the cylinder cover.
Oil seal
Sharpen wedge
6
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra LS520D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra LS520D in the language / languages: English as an attachment in your email.

The manual is 17,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info