634449
5
Zoom out
Zoom in
Previous page
1/10
Next page
L
Mains connection
Comp
are the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the machine
to the relevant and properly earthed pl
ug.
Only use connection cables with sufficient diameters.
Connect the machine via a 30 mA fault current safety
switch.
L
Fuse protection: 13 A
L Operating pushbutton
Fig. 2
Operating pushbutton
Switching on
Push
the green button. The motor is running as long as the
green button remains pushed.
Switching off
Stop pushi
ng the green button.
Do
not use any device where the operating pushbutton
does not work properly. Repair or replace damaged
pushbuttons immediately.
L
Hydraulics
Neve
r operate the machine in the event of any possible
danger from hydraulic fluid.
Ensure that the machine and working area are clean and
free of oil.
Danger of slippage or fire!
Check the hydraulic reservoir regularly to ensure that it
contains enough hydraulic oil (see “Care and
maintenance”)
Capacity: 3.2 litres
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
l
l
o
o
g
g
s
s
p
p
l
l
i
i
t
t
t
t
e
e
r
r
additional SAFETY INSTRUCTIONS
The log s
plitter may only be operated by a single person.
The machine may only be operated by persons over the
age of 18 years, and who have read and understood these
operating instructions.
Wear protective equipment (safety goggles/mask, gloves,
safety shoes) to protect yourself from possible injury.
Never try to split logs containing nails, wire or other similar
objects.
Already split wood and wood chips create a dangerous
working area. The operator may stumble, slip or fall
.
Always keep the working area neat and tidy.
Never place the hands on or near any moving parts of the
machine when it is switched on. Maintain a safe distanc
e
from the log, the ram and the wedge in order to protect
your hands from injury.
Split only timber which corresponds to the maximal length
to be worked with.
What type of logs can I split?
Size of logs
Lengt
h: max. 520 mm
Diameter: 50 – 250 mm
The log diameter is a recommended guideline figure, because:
thin logs can be difficult to split if they contain knots or if
the fibres are too strong.
logs with a diameter of over 250 mm can be split if the
fibres are smooth and open.
Do not try to split green logs. Dry logs are much easier to split,
and do not cause jams as often as green (damp) wood.
Operation
Two-hand operation
1. Press th
e operating pushbutton on the electric motor. Wait
a few moments until the motor has reached its operating
revolutions and the required pressure has been built up in
the hydraulic pump – Fig. 3.
2. Press the operating lever down simultaneously – Fig. 3.
Î The log ram pushes the log against the splitting
wedge, and the log will be split.
3. Release the operating lever as well as the operating
pushbutton. The log ram will now return to its origi
nal
starting position – Fig. 4.
4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra LS520D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra LS520D in the language / languages: English as an attachment in your email.

The manual is 17,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info