634449
4
Zoom out
Zoom in
Previous page
1/10
Next page
Damage
d guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
Dama
ged or illegible safety warning labels should be
replaced immediately.
Electrical safety
Electric
al connections must conform to IEC 60245 (H 07
RN-F) with a cable cross-section of at least
2.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over
10 m in length. Longer power supply cables will cause a
drop in voltage. The motor will not be able to provide its
maximum performance and the operation of the machine
will be im
paired.
When laying the connecting attachments, be sure that
they do get crushed or bent, and that the plug-and-socket
connection does not get we
t.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Re
gularly check the extension cables and replace them if
they are damage
d.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass prot
ective devices or deactiva
te them.
The ele
ctrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures
must be observed.
Repa
irs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points.
Us
e only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
Fig. 1
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
i
i
n
n
g
g
Positi
on the log splitter on a work surface at a height of about
60 – 75 cm, this will create an comfortable working position.
Place chocks under the wheels to prevent the machine rolling
during operation.
Ensure that the working area meets the following conditions:
no danger of slipping
level
free of obstacles
sufficiently well lit
Do not operate the machine in the direct vicinity of gas or
petrol pipes or containers, or any other easily inflammable
materials.
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Check that the machine is completely and correctly
assembled.
Before usin
g the splitter, make sure each time that
there are no faulty connections (tears, cuts, etc.)
there are no damage at the machine
all screws are tight
check the hydraulic system for any possible leaks
3
1.hydraulic tank
3.frame tube
5.electric motor
7.push button
2.splitting wedge
4.log ram
6.switch
8.plug
9.wheel 10.operating lever
11.support leg 12.handle
13.extension leg
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra LS520D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra LS520D in the language / languages: English as an attachment in your email.

The manual is 17,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info