Manual Clatronic BZ 3740 (page 48 of 78) (English, German, Dutch, French, Italian, Polish, Spanish)

686431

Zoom out

Zoom in

1/78

BZ3740_IM 07.03.19

3. Turn the pressure regulator to the “ ” position.

4. Use the button to open the lid of the appliance.

5. Remove the CO

feed valve

from the connector on the

tting. To do this, press the

white release button labeled

“PRESS” that is located on

the tting.

6. Insert a new 16 g CO

cartridge into the holder as

described in the chapter “Inserting the Carbon Dioxide

(CO

) Cartridge”.

Dismantling Beer Dispenser

To clean the beer dispenser and / or to replace the keg,

it is necessary to remove the dispensing unit from the

dispenser.

CAUTION:

Never remove the dispensing unit from the keg while it is

still pressurized.

1. Switch off the appliance.

2. Disconnect the mains plug from the socket.

3. Turn the pressure regulator to the “

” position.

4. Use the button to open the lid of the appliance.

5. Remove the CO

feed valve from the connector on the

tting. To do this, press the white release button labelled

“PRESS” that is located on the tting.

6. Place a container underneath the beer tap.

7. Keep the tap handle pressed until the appliance is no

longer pressurized. There must be no more beer or

foam escaping.

8. Remove the beer hose from the beer connection valve

of the dispensing unit. To do this, press the white release

button labelled “PRESS” that is located on the tting.

9. Now you are able to remove the keg with the dispensing

unit from the tank of the appliance.

NOTE:

This may require some effort due to the keg being

secured by a suction cup located at the bottom of the

appliance.

10. Detach the dispensing unit from the

keg:

See the adjacent gure. First, re-

move the right holder. Then push the

left holder out of the keg’s edge.

11. Remove the dispensing unit from the

keg by evenly pulling it out.

NOTE:

As the beer tap may not be moist during extraction,

removal may take some effort.

12. The dispensing unit can now be cleaned as described

in the chapter “Cleaning” and subsequently installed

on a new keg as described in the chapter “Piercing the

Beer Keg”.

NOTE:

If necessary, replace the CO

cartridge as described

in the chapter “Replacing the Carbon Dioxide (CO

)

Cartridge”.

Water Change

There is no need to change the water in the tank every time

a beer keg has been emptied. Exchange the water weekly.

1. Remove the collecting tray from the appliance.

2. After disconnecting the appliance from the power supply,

place it near a table edge and make sure the front feet

are still on the table.

3. Place an empty container than can hold about 1 litre of

water under the edge of the table.

4. To open the outlet, pull the drain lever down. The tank

gets emptied.

5. Use a clean cloth to wipe the tank.

6. Release the drain lever.

7. Use clean water to ll the tank up to the MAX mark.

8. Repeat the procedure in order to rinse the tank.

Cleaning

WARNING:

• Before cleaning, always remove the mains plug and wait until

the appliance has cooled down.

• Do not immerse the appliance in water. Otherwise this might

result in an electric shock or re.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic BZ 3740 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic BZ 3740 Manual

Product: