Manual Clatronic BZ 3740 (page 47 of 78) (English, German, Dutch, French, Italian, Polish, Spanish)

686431

Zoom out

Zoom in

1/78

BZ3740_IM 07.03.19

Operation

CAUTION:

Before switching of the beer dispenser, always ensure

that no 5 litre party keg is present in the dispenser as the

beer in the keg becomes warm and is no longer fresh.

Close the lid of the appliance. It must audibly snap.

Electric Connection

1. Ensure that your mains power corresponds with the

specications of the appliance. The specications are

printed on the type label.

2. Connect the mains cable to a properly installed and

earthed wall outlet.

Turning the Appliance On / Off

• Set the switch to the “ I ” position to turn the appliance on.

• The appliance is turned off when in the “

” position.

Temperature Adjustment

NOTE:

The appliance saves the most recently set cooling tem-

perature while switching it off.

After switching the appliance on again, the display will show

the current temperature of the inserted beer keg and the

last set cooling temperature.

• You can choose a cooling temperature ranging from 2 °C

to 12 °C.

• In order to display the set temperature, you may briey

press the

or button.

• Press and hold the or button to adjust the temper-

ature setting.

Pressure Regulator for Carbon Dioxide

(Exception: Heineken kegs)

Use the pressure regulator to select the appropriate pres-

sure for your beer. As different beer varieties are carbonated

to a differing extent, different pressures (saturation pres-

sure) are required to ensure the quality of the respective

beer. If a beer is dispensed with insufcient pressure, for

example, it can make the beer taste at, whilst too much

pressure can make it too zzy. If the beer should be too

zzy or at, simply adjust the pressure accordingly. To be

noted is that the CO

content in the beer initially changes

over the course of time.

NOTE:

Make sure the pressure regulator is always in the “

”

position when

• the beer drawing procedure is interrupted.

• you replace the CO

cartridge or the keg.

• In case you can no longer draw beer, even though there

is still beer in the keg, or foaming requires too much

time, slowly turn the pressure regulator towards “

” for

5 seconds. Then set the pressure regulator back to the

“

” position.

Drawing Beer

1. Preparing glasses

Wash the glasses in hot water with a small amount of

washing / up liquid. Rinse the glasses thoroughly each

time before dispensing with cold, clear water.

Ensure that all grease and residues are removed com-

pletely to avoid impairing foam formation.

NOTE:

The best results can be achieved by using glasses

exclusively for beer to ensure that no residues from fat

containing drinks (e. g. milk) are present.

2. Dispensing beer

Hold the glass under the beer tap at an angle. The tip

of the outlet tube should not come into contact with the

glass as this can impair the foam formation.

NOTE:

The foam produced when dispensing beer can be

inuenced by changing the angle of the glass.

Pull down the tap handle in one motion.

NOTE:

If the tap is only partly open, the beer may foam exces-

sively as it is not able to ow out freely.

Allow the beer to run down the inside of the glass and

slowly straighten the glass while dispensing until it is

upright towards the end.

When the foam reaches the rim of the glass, close the

beer tap by pushing back the beer tap handle.

Place the glass on the drip plate and wait until the foam

has settled. Ensure that the glass is not located directly

under the beer tap so that no drops fall into the bear

foam.

Repeat the dispensing process until the beer and foam

are in the correct proportion. This is the case when the

head is about two nger’s breadth high and slightly over

the rim of the glass.

Replacing the Carbon Dioxide (CO

) Cartridge

(Exception: Heineken kegs)

WARNING for frostbite:

• Do not remove the CO

cartridge before it is com-

pletely emptied.

• A residual amount of CO

may still be present in the

cartridge, which suddenly empties and results in the

formation of ice.

Once no beer can be drawn, even though the pressure

regulator is in the “

” position and there is still beer in the

keg, replace the CO

cartridge.

1. Switch off the appliance.

2. Disconnect the mains plug from the socket.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic BZ 3740 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic BZ 3740 Manual

Product: