517230
24
Zoom out
Zoom in
Previous page
1/64
Next page
24
Step 13:
Installation of Stepper and Crossbar (22) at support 1
(4).
1. Place the crossbar (22) into appropriate position at support
1 (4) and rear foot (2), so that the holes are align and screw
it tightly by using screw M10x70 (112), washers 10//20 (118)
and self locking nut M 10 (124). (Note: Perhaps you have to
loosen the connection point of support 1 (4) and rear foot (2)
a little bit to mount crossbar easy.)
2. Put the left and right pedal (21+24) in right direction at
appropriate holder at support 1 (4), that the steel bearings
align and slide the axle 1 (34) through. Secure the axle 1(34)
by using screw M8x15 (99), spring washer for M8 (123) and
washer 8//38 (120) on both ends of axle.
3. Put the hydraulic cylinder (58) with top side onto the
holder of crossbar (22) and secure this position by using
screw M8x15 (99), spring washer for M8 (123) and washer
8//28 (121).
4. Scew the bottom end of cylinder (58)at the holder for
cylinder (46) by using screw M8x40 (103), washer 8//16 (117)
and self locking nut M 8 (125). Ensure that the cylinder (58)
can turn at holder a little bit.
5. Insert the holder for hydraulic cylinder (46) from top side
trough the pedal left and right (21+24) and connect the holder
(46) into desired position by using handgrip nut (75) and
washer 10//38 (120). You can adjust the stepper resistance
at holder (46) by choosing different positions at pedal left
and right (21+24)
6. Put a cable roller unit as fi gure „A“ show together, put the
cable 5 (59) over the pulley (83) and connect this at cable
pulley holder incl. hook (35) in a way that the cable pulley
can roll easy.
7. Insert the cable pulley holder incl. hook (35) into the welded
holder at crossbars‘ (22) bottom side and connect the ends
of cable 5 (59) with the pedal left and right (21+24).
Step 14:
Installation of cable 1 for latissimus (26) with cable pulley
units. Please note following situation regarding the cable
pulley units: The cables have to put on the cable pulleys
(83) and should covered on both sides with cable pulley
covers (84) that the input and output of cable is leaded.
The cable pulley units have to install at the same time
with cables at right position.
1. Put the cable 1 (26) as showed in Step 14 drawing through
the top cross beam (5), screw the screw end of cable 1 (26)
with washer 12//24 (119) into the weight disk bar (40) and
secure the screw with nut.
2. Take cable 1 (26) and a cable pulley unit as showed in
gure „A“ (without cable pulley cover) with screw M10x70
(112), washer 10//20 (118), plastic bushing for pulley (94) and
nut M10 (124). Insert the cable pulley (83) into the top cross
beam (5), position the plastic bushing (94) from outer side of
top cross beam (15) and screw in tightly.
3. Put a cable roller unit as fi gure „B“ shows together with
screw M10x45 (110), washer (118) and self locking nut (124),
insert the cable 1 (26) and connect this at top cross beam
(5).
4. Take cable 1 (26) and a cable pulley unit as showed in
gure „B“ with screw M10x70 (112), washer 10//20 (118),
plastic bushing for pulley (94) and nut M10 (124) and attach
it at cable pulley holder 2 (6).
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit Profi-Center - 99881 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Profi-Center - 99881 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Christopeit Profi-Center - 99881

Christopeit Profi-Center - 99881 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info