Manual Charnwood Cove 2B (page 11 of 16) (English)

632314

Zoom out

Zoom in

1/16

Fig.9. Vertical register plate with bricked up fireplace

Fig. 10. Horizontal register plate with rear flue connection

If the appliance is used to heat a small central heating system then the

heat output to the room from the fire will be reduced.

Fitting a radiator in the same room as the fire is recommended as it

will allow greater flexibility in the way that the system is operated as

well as ensuring that there is sufficient heat.

Connect the heating system to the boiler ensuring that the primary

flow pipe rises continuously from the appliance to the vent. Fill the

system with water and check for leaks.

The circulating pump may be controlled by means of time switches,

room thermostats or outdoor thermostats. Radiators may be either

manually or thermostatically controlled. These controls will all work

in conjunction with the thermostat on the appliance and the low limit

pipe thermostat.

We recommend fitting a pipe thermostat onto the gravity return to

act as a low limit thermostat This should be wired into the mains

supply to the pump so that if the gravity return temperature drops

below 45°C then the pump will cut out. This will help to prevent

condensation forming on the boiler faces and will thereby increase

the life of the boiler. It will also ensure that priority is given to the

domestic hot water. These thermostats are available from

Charnwood if you are unable to obtain them locally.

If the vertical rear flue connector (shown in Fig. 12) is used then the

chimney may be swept through the appliance.

Horizontal lengths of flue must be kept to a minimum and should not

be more than 150mm (6 inches) long. The sealing face of the flue

collar should be coated with fire cement before fixing to the body of

the stove using the two screws provided. The blanking plate must be

removed, sealed with fire cement and refitted, care being taken to

ensure that the fold on the clamping plate is in line with the lugs on

the firebox as shown on the label on the clamping plate. Ensure that

the clamping plate does not prevent the throat plate from seating

correctly. All flue connections must be well sealed.

It is possible to pass a 16 inch diameter sweeps brush through the

appliance but in most back outlet installations it will be necessary to

have a soot door to enable the chimney to be swept. This may either

be in the actual brickwork of the chimney or in the register plate.

SYSTEM CONTROLS

CONNECTIONS TO FLUES

SOOT DOORS

There are several ways of connecting the stove to the flue. These are

illustrated in figures 9 to 12.

Various types and positions of soot doors are shown in figures 9 to

12.

The stove arrives bolted and shrink-wrapped to its pallet. The

wrapping is first removed, then the stove released from the pallet by

removing the 4 pallet bolts using a 10mm spanner. The pallet brackets

can now be removed from the stove by tilting it and using a 13mm

spanner to remove the bolts. These 4 bolts are required for levelling

on the Low Stand or fixing on the Centre Stand, but are not used on

the Store Stand. The Stove comes with the Low Stand fitted and if

this is to be used, the Stove may now be moved to its final position.

The pallet is intended to be cut up and used for kindling fuel.

The Stand is first positioned on the hearth in the desired position of

the stove. The lower cover must be removed from the stove by first

unscrewing the air control knob, then removing the 6mm bolt on

each side using a 4mm allen key. The Cover may now slide off. Ensure

UNPACKING THE STOVE

FITTING THE STOVE TO ITS STAND

1. Centre stand

Alternative Soot Door Positions

With Soot Door

Soot Door

in side or rear

of Chimney

charnwood

INSTALLATION INSTRUCTIONS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Cove 2B in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Charnwood Cove 2B

Charnwood Cove 2B User Manual - French - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Charnwood Cove 2B Manual

Product: