632314
12
Zoom out
Zoom in
Previous page
1/16
Next page
that the pallet brackets have been removed from the stove, then lift
the stove on to the stand, aligning the 4 tapped holes in the base
brackets with the 4 slots in the top of the stand. NOTE: This requires
at least 2 people. The stove is fixed to its stand using 4 M8 x 20mm
bolts and 4 plain washers. A 13mm open ended spanner is required.
Replace the cover, side bolts and Air Control Knob.
2. Store stand
Place the Store Stand on the hearth, with at least 100mm clear space
behind it. Remove the lower cover as described above - it is not used.
With 2 people, carefully lift the stove on to the stand such that the
front end of the Air Control Rod is lowered down inside the stand.
Take care not to bend or damage the Air Control Rod. Temporarily
rest the stove on the stand in this position and pull the Air Control
Rod through the hole in the front of the stand. Now move the stove
towards you to align the slots in the side of the stand with the 6mm
tapped holes in the base brackets. Fix in position with the bolts that
Fig. 12. Horizontal register plate with optional vertical rear flue connector
Alternative
Soot Door
Positions
Register Plate
With Soot Door
Fig. 11. Horizontal register plate with top flue connection
Alternative
Soot Door
Positions
Register Plate
With Soot Door
1
2
2
2
3
4
4
were used to secure the cover and replace the Air Control Knob.
Before initial lighting the following points should be checked:
1. The bottom grate bars must all be fitted and should move freely
and easily when the riddling mechanism is operated.
2. The plates round the sides and back of the grate must be in
position and sitting correctly.
3. The throat plate must be fitted in the roof of the appliance and
should be checked to ensure that it has not become dislodged in
transit. The method of location and positioning of the throat plate is
shown in Fig. 4.
4.
On completion of the installation and after allowing a suitable period
of time for the fire cement and mortar to dry out, the stove should
be lit and checked to ensure that smoke and fumes are taken from
the appliance up the chimney and emitted safely. Also check all joints
and seals. On completion of the installation and commissioning please
leave the operating instructions with the customer and advise them
on the use of the appliance.
The heating system must be correctly connected and filled with
water before lighting the fire. Lighting the fire without water in
the boiler can cause serious damage to the boiler and will
invalidate the guarantee.
PRE LIGHTING CHECK
COMMISSIONING
®
Fig. 13
12
charnwood
INSTALLATION INSTRUCTIONS
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Cove 2B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Cove 2B in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Charnwood Cove 2B

Charnwood Cove 2B User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info