632314
10
Zoom out
Zoom in
Previous page
1/16
Next page
sought either from the supplier or the local building inspector.
The fireplace must allow good circulation of air around the appliance
to ensure that maximum heat is transferred to the room and also to
prevent the fireplace from overheating. A gap of 150mm (6 inches)
each side and 300mm (12 inches) above the appliance should give
sufficient air circulation. If a wooden mantelpiece or beam is used in
the fireplace it should be a minimum of 460mm (18 inches), and
preferably 600mm (24 inches) from the appliance. In some situations
it may be necessary to shield the beam or mantelpiece to protect it.
In order for the fire to operate correctly there must be an air gap
behind the appliance of at least 40mm, but be aware that this
distance will need to be greater in some cases to meet Building
Regulation requirements.
CENTRAL HEATING SYSTEM
The central heating system must comply with BS EN 14336, BS EN
12828 and BS EN 12831.
The installation of any electrical services during the installation of this
boiler and the associated heating system must be carried out by a
registered competent electrician and in accordance with the
requirements of the latest issue of BS 7671.
If the system is to be a combined heating and domestic hot water
system then a double feed indirect hot water storage cylinder to
BS:1556 part 1 should be used. In order to prevent the build up of
scale and corrosion a suitable inhibitor should be used. The system
must be correctly vented as shown in Figs. 6 and 7. The height
differential between the header tank and the appliance must not
exceed 15.2 metres (50 feet).
If all four boiler tappings are used then, if possible, diagonal pairs
should be connected for domestic hot water and central heating.
Where a common return is used an injector tee must be
incorporated into the system as shown in Fig.8. This will ensure that a
good domestic hot water supply is maintained when the central
heating pump is operating.
The system must incorporate a gravity circuit which will normally
heat the domestic hot water and an unvalved radiator with an output
of at least 1 kW. When the appliance is not connected to a domestic
hot water system the unvalved radiator(s) on the gravity circuit must
have an output of at least 1.25 kW. This is to prevent boiling in case
of pump failure. All pipework in the primary circuit must be 28 mm
diameter and the gravity flow pipe must rise continuously from the
boiler to the open vent. Two typical systems are shown in Figures 6
and 7.
Gravity Return (28mm Pipe)
Central Heating
Return
Common
Return to Boiler
(28mm Pipe)
Fig. 8. Injector Tee
Fig. 7. Typical Central Heating & Hot Water System
Using 3 Tappings
®
Central Heating Flow
Central Heating Return
Drain Cock at Lowest Point
Drain Cock
Gravity Return 28mm
Gravity Flow 28mm
Indirect Hot Water Cylinder
Cold Water Tank
Overflow
Feed and
Expansion
Tank
22mm Open Vents
Gravity
Radiator
Circulating Pump
Minimum Return
Thermostat
Overflow
Domestic Hot Water
Draw Off
Fig. 6. Typical Central Heating & Hot Water System
Using 4 Boiler Tappings
10
Central
Heating Return
Drain Cock at Lowest Point
Cold Water Tank
Circulating Pump
Drain Cock
Gravity Return 28mm
Gravity Flow 28mm
Indirect Hot Water Cylinder
Domestic Hot
Water Draw Off
Overflow
Overflow
Feed and Expansion Tank
22mm Open Vents
Gravity Radiator
Central
Heating Flow
Minimum Return Thermostat
charnwood
INSTALLATION INSTRUCTIONS
Injector Tee
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Cove 2B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Cove 2B in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Charnwood Cove 2B

Charnwood Cove 2B User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info