667040

Celestron CGE Pro 925 Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
8
O
O
n
n
e
e
P
P
e
e
r
r
s
s
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
As an alternative to the method described above, The CGE Pro mount can be more easily assembled by one person if the polar
housing axis is installed separately from the latitude side plates. To do this you must first lay the equatorial head on a flat soft
surface and remove the two sections.
1. Remove the latitude indicator from the polar housing.
2. Remove the two bolts that connect the polar housing to the
latitude side plate assembly, and loosen (but do remove) the
two pivot bolts.
3. With the electronics pier securely attached to the tripod, mount
the latitude side plate assembly to the pier as described in the
section above.
4. Before mounting the polar housing, make sure that the RA
locking clutches are secure so that the housing can not rotate
while being installed. Also rotate the latitude adjustment bolt
counterclockwise until only about an inch of thread is
protruding downward.
5. Lift the polar housing section and carefully lower the polar
axis between the side plates (and beneath the latitude
adjustment bolt) until the pivot bolts rest inside the two cut
outs on the side plates.
6. Once seated, attach the two bolts connecting the polar housing
to the side plates.
7. Reattach the latitude indicator from the polar housing.
8. Rotate the latitude adjustment bolt until the angle of the polar
axis approximately matches the latitude of your current
location.
A
A
d
d
j
j
u
u
s
s
t
t
i
i
n
n
g
g
t
t
h
h
e
e
L
L
a
a
t
t
i
i
t
t
u
u
d
d
e
e
P
P
l
l
a
a
t
t
e
e
As shipped from the factory, the CGE Pro mount will only adjust to a maximum latitude of about 40 degrees. If using the
mount from a latitude higher than 40 degrees you will need to change the position of the latitude plate and adjustment bolt.
To change the position of the Latitude Plate:
1. Remove the polar housing section from the mount as described in the One Person Installation section above.
2. Use a 5mm Allen wrench to remove the four latitude
plate screws (fig 2-4) from the side plate assembly.
3. Lower the latitude plate until the holes line up with the
lower set of latitude plate holes.
4. Thread the four latitude plate screws back into the
latitude plate.
Polar
Housing
Section
Latitude Side
Plate Assembly
Latitude
Adjustment Bolt
Pivot Bolts
Cutouts for
Pivot Bolts
Latitude
Indicator
Attachment
Bolts
Figure 2-3
Latitude Plate Screws –
For 40° latitude and lower
Latitude Plate Screws –
For 40° latitude and higher
Figure 2-4
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CGE Pro 925 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CGE Pro 925 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info