667040

Celestron CGE Pro 925 Manual

10
Zoom out
Zoom in
Previous page
1/72
Next page
10
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
O
O
p
p
t
t
i
i
c
c
a
a
l
l
T
T
u
u
b
b
e
e
t
t
o
o
t
t
h
h
e
e
M
M
o
o
u
u
n
n
t
t
The telescope attaches to the mount via a dovetail slide bar which is mounted along the bottom of the telescope tube. Before
you attach the optical tube, make sure that the declination and right ascension clutch knobs are tight (see Figure 2-14)
and the counterweight(s) are securely installed.
This will ensure that the mount does not move suddenly while attaching
the telescope. To mount the telescope tube:
1. Make sure that the direction arrow on the mounting platform (Fig 2-7) is
point up towards the sky. If the arrow is pointing downward you must
loosen the DEC locking knobs to rotate the mounting plate and re-tighten
the locking knobs.
2. Loosen the three mounting screws (do not remove them) on the side of the
telescope mounting platform. This allows you to slide the dovetail bar
onto the mount.
3. Remove the safety screw located at the front of the dovetail bar.
4. Slide the dovetail bar on the telescope tube into the mounting platform of
the mount. Slide the telescope so that the back of the dovetail bar is close
to the back of the mounting platform.
5. Tighten the mounting screw on the side of the mounting platform to hold the telescope in place.
Now that the optical tube is securely in place, the visual accessories can now be attached to the telescope.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
V
V
i
i
s
s
u
u
a
a
l
l
B
B
a
a
c
c
k
k
The visual back is the accessory that allows you to attach all visual accessories to the telescope. The telescope optical tubes
come with the visual back installed. If it is not already on the tube it can be attached as follows:
1. Remove the rubber cover on the rear cell.
2. Place the knurled slip ring on the visual back over the threads on the rear cell (Fig 2-9).
3. Hold the visual back with the set screw in a convenient position and rotate the knurled slip ring clockwise until tight.
Once this is done, you are ready to attach other accessories, such as eyepieces, diagonal prisms, etc.
If you want to remove the visual back, rotate the slip ring counterclockwise until it is free of the rear cell.
Figure 2
-
8
Direction
Arrow
Figure – 2-7
Safety
Screw
Dovetail Bar
Telescope Mounting Screws
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CGE Pro 925 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CGE Pro 925 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info