667040

Celestron CGE Pro 925 Manual

7
Zoom out
Zoom in
Previous page
1/72
Next page
7
3. Slide the center portion of the tripod leg away from the tripod head until it is at the desired height.
4. Tighten the levers on each leg clamp to hold the legs in place.
5. Once that it is fully assembled, rotate the tripod so that one of the legs is pointing roughly towards north.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
A
A
c
c
c
c
e
e
s
s
s
s
o
o
r
r
y
y
T
T
r
r
a
a
y
y
1. Slide the accessory tray over the central rod so that the three cup indents are pushing against the inside of the tripod legs.
2. Thread the accessory tray knob on to the central rod and tighten.
To transport your tripod, remove the knob and lower the accessory tray far enough to rotate it until the three recesses line up
with each leg. Collapse the legs so that each leg falls into one of the recesses. Secure the legs together with the nylon strap
attached to the tripod leg.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
E
E
l
l
e
e
c
c
t
t
r
r
o
o
n
n
i
i
c
c
s
s
P
P
i
i
e
e
r
r
Before the equatorial mount head can be installed, the electronics pier must be attached to the tripod. To attach the pier:
1. Position the electronics pier so that the electronics
module is right side up (with the printing readable).
2. Place the bottom of the pier over the tripod head.
3. Rotate the column until the three holes line up with
the threaded holes on the side of the tripod head. The
pier should be positioned so that the motor ports
(labeled RA and DEC) are on the east side of the
mount. (see figure 2-4)
4. Insert the three 3/8-16 Allen head screws and washers
provided through the holes in the electronics pier and
into the tripod head.
5. Tighten the screws to hold the column securely in
place.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
E
E
q
q
u
u
a
a
t
t
o
o
r
r
i
i
a
a
l
l
M
M
o
o
u
u
n
n
t
t
After the tripod is set up, you are ready to attach the equatorial
mount. The equatorial mount is the platform to which the
telescope attaches and allows you to move the telescope in
right ascension and declination. To attach the equatorial mount
to the tripod:
1. Insert the base of the equatorial mount into the top of
the electronics pier.
2. Rotate the equatorial mount on the electronics pier
until the holes in the mount line up with those in the
pier and the DEC opening (where the counterweight shaft will go) is positioned directly over the north tripod leg.
3. Insert the three remaining 3/8-16 screws and washers provided through the holes in the electronics pier and into the
equatorial mount.
4. Tighten the screws to hold the equatorial mount in place.
North Leg
Electronics Pier
Tripod Head
Equatorial
Mount
Figure 2-2
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CGE Pro 925 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CGE Pro 925 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info