544063

Bosch PPR 250 Manual

19
Zoom out
Zoom in
Previous page
1/184
Next page
English | 19
Bosch Power Tools 2 609 006 717 | (26.11.13)
Correction of Malfunctions
Maintenance and Service
Before any work on the machine itself, pull the mains
plug.
Cleaning
After painting, the system must be pumped empty and all
paint-carrying parts must be cleaned.
There are two possibilities for cleaning the system:
– EasyClean: Using universal connectors, the system is con-
nected to a water tap and flushed.
– Alternative possibility: The system pumps fresh water
from a bucket for cleaning.
Proper cleaning is a prerequisite for perfect operation of the
electric paint roller. No warranty claims can be undertaken if
cleaning is not carried out or is carried out incorrectly.
Keep the base unit, the holding clip 28 and the remote control
8 clean. Clean them with a moist cloth. The base unit and the
remote control may not be immersed into water.
Always clean the paint roll, the paint applicator and the hose
system with water.
Preparation
– Place down the paint applicator 3 on the edge of the paint
bucket so that it rests on the bucket holder 14.
– Loosen the double-SDS-connector 27 from the holding
clip 28 and completely remove the intake hose 4 and the
paint filter 22 from the paint bucket.
– Remove the paint roll 16 from the paint applicator 3 (see
“Changing the Paint Roll”, page 18).
– Hold the paint applicator 3 above the paint bucket and press
the trigger switch 7 until the hose system is pumped empty
and no more paint comes out of the paint applicator.
– Release the trigger switch 7 and switch the power tool off.
– Pull the mains plug from the socket outlet.
EasyClean (see figures G1 –G4)
Note: Use only the supplied hoses and adapters for connect-
ing to the water supply.
Preparing the water tap:
– Unscrew the mixing nozzle from a water tap using the sup-
plied mixing-nozzle spanner 30 or a suitable tool.
– Screw the fitting adapter 31 (M22 or M24 thread) in or on
the water tap.
Additional water-tap adapters are available in the Bosch
accessories program.
Separating paint-carrying components:
– Unlatch holding clamp 21.
– Disengage pump lock 23.
To relieve the lock tension, lightly push the pump lid 20 up-
ward, if required.
– Push the pump lid 20 downward to the stop and then care-
fully lift it out of the housing opening of base unit 5.
– Loosen the SDS connection 32 at the bottom part of the in-
take hose 4.
Flushing the system:
– Carry the paint applicator 3, feed hose 2, pump lid 20 and
intake hose 4 to the prepared water tap.
Please note that paint may escape or leak from the system.
Problem Cause Corrective Measure
Paint application unsatisfactory.
The hoses are obstructed. No or too little
paint being transported.
Make sure that none of the hoses are
squeezed or creased.
The paint is too viscous and therefore
cannot be transported.
Stir the paint thoroughly and dilute it with
5 –10% water if necessary.
The pump lock 23 is not engaged. Make sure that pump lid 20 is properly in-
serted and locked.
The paint bucket is empty. Refill the paint bucket with fresh paint or ex-
change the empty paint bucket against a full
one.
No paint coming out of paint applicator 3.
The paint is too viscous and cannot be
drawn in by the pump.
Stir the paint thoroughly and dilute it with
5 –10% water if necessary.
The hoses are obstructed. Clean the hose system (see “Cleaning”,
page 19).
The hoses are obstructed. No or too little
paint being transported.
Make sure that none of the hoses are
squeezed or creased.
The remote control 8 is inoperative. The base unit is switched off. Switch the base unit on (see “"Switching
On"Switching On”, page 18).
The remote control battery is empty. Contact an authorised service agent for
Bosch power tools.
Have the component replaced there.
Note: The battery never has to be replaced
in normal use.
OBJ_BUCH-1513-004.book Page 19 Tuesday, November 26, 2013 4:07 PM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PPR 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PPR 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info