Manual Bosch PPR 250 (page 20 of 184) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544063

Zoom out

Zoom in

1/184

20 | English

2 609 006 717 | (26.11.13) Bosch Power Tools

– Attach the double-SDS-connector 27 to adapter 31 on the

water tap.

– Hold the paint applicator 3 over a suitable collecting con-

tainer (e. g. a bucket).

– Carefully open the water tap and run lukewarm water

through the system.

– When flushing, lightly press pump hose 33 together sever-

al times.

This will lead to better cleaning results.

Additionally, this also cleans bypass hose 34, which pre-

vents the rotor from overloading in case of excessive pres-

sure in the hose system.

– Flush the system until only clear water comes out of the

paint applicator.

– Clean the paint filter 22 and the intake hose 4 (connect

SDS connection 32 to the water tap and flush; additional

cleaning of paint filter with brush).

– Release the adapter 31 from the water tap and from the

double-SDS-connector 27.

Screw the mixing nozzle back onto water tap.

Cleaning the paint applicator and the paint roll:

– See “Cleaning the Paint Applicator and the Paint Roll”,

page 20.

Mounting together the dried components:

– Allow all components to dry thoroughly.

If possible, hang up the paint roll 16 to dry.

If the paint roll is placed down to dry, the pile will be de-

formed. This may lead to an uneven surface quality when

using the paint roller the next time.

– Reconnect the intake hose 4 to the SDS connection 32 on

the paint filter 22.

– Manually turn rotor 35 to the indicated position (see figure

G4) in order to avoid damage to pump hose 33 when in-

serting pump lid 20.

– Reinsert the pump lid 20 into the housing opening and

push it upward to the stop.

– Shut pump lock 23 until it engages.

–Lock holding clamp 21 again.

Alternative Cleaning Method (see figure H)

Note: This cleaning method takes somewhat longer than the

EasyClean method.

–Couple base unit 5 to the water bucket (also see “Coupling

the Base Unit and the Paint Bucket”, page 17).

– Insert paint filter 22 to the bottom of the water bucket.

– Fasten the intake hose 4 in the holding clip 28.

– Plug the mains plug into a socket outlet.

– Make sure that the pump lock 23 is engaged.

–To start

the machine, push the On/Off switch 18 to the “I”

position.

– Hold paint applicator 3 over a suitable collecting container

(e.g. a bucket) and actuate trigger switch 7 until only clear

water comes out of the paint applicator and no more paint

can be seen in the hoses (visual check).

Always lightly move the hoses.

This will lead to better cleaning results.

– Clean the paint applicator and the paint roll: See “Cleaning

the Paint Applicator and the Paint Roll”, page 20.

– Allow all components to dry thoroughly.

If possible, hang up the paint roll 16 to dry.

If the paint roll is placed down to dry, the pile will be de-

formed. This may lead to an uneven surface quality when

using the paint roller the next time.

Cleaning the Paint Applicator and the Paint Roll

(see figures I1 –I3)

After flushing the system, some of the components still have

to be cleaned manually.

– Remove paint remainders from paint applicator 3 using a

brush.

– Pull paint distributor 36 out of the paint chamber 37.

For easier cleaning, turn the paint distributor by 90°.

– Remove the distributor plate 38 from the paint distrib-

utor 36.

For this, lift the distributor plate on one side and pull it lat-

erally out of the retaining clamps.

– Remove paint remainders from of the distributor plate 38,

the paint distributor 36 and from of the paint chamber 37

using a small brush.

– Wash out the paint roll 16 thoroughly.

Storage

Before storing, the electric paint roller must be properly

cleaned and all components dried.

– Slide distributor plate 38 laterally into the retaining clamps

in paint distributor 36.

– Clip paint distributor 36 into the paint chamber 37.

– Wind up feed hose 2 around the base unit 5 and affix it with

holding clamp 21.

– Slide down paint-bucket coupling 29 completely to the

bottom.

– Insert paint roll 16 into paint applicator 3 (see “Changing

the Paint Roll”, page 18).

Material Disposal

Paint and dried paint remainders must be disposed of in an

environmentally-friendly manner. Observe the manufactur-

er’s instructions for disposal and the local regulations for haz-

ardous waste disposal.

Chemicals harmful to the environment may not be disposed of

into soil, groundwater or bodies of water. Never pour chemicals

harmful to the environment into the sewerage system!

Maintenance

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

OBJ_BUCH-1513-004.book Page 20 Tuesday, November 26, 2013 4:07 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PPR 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PPR 250 Manual

Product: