Manual Bosch PPR 250 (page 18 of 184) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544063

Zoom out

Zoom in

1/184

18 | English

2 609 006 717 | (26.11.13) Bosch Power Tools

The paint bucket handle must always be positioned be-

tween the hooks of the paint-bucket coupling.

– Insert the paint filter 22 to the bottom of the paint bucket.

– Fasten the intake hose 4 in the holding clip 28.

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

 Always place the base unit and the paint bucket on a

level surface. When operating the paint roller on a ladder

or an inclined surface, the base unit and the paint bucket

can tip over or fall down. This can lead to injury and con-

tamination from the coating material.

 Do not cover off the base unit. Otherwise, a possible mal-

function cannot be detected.

 Keep other electrical machines/devices away while

using the paint roller or cover them off adequately.

Possibly occurring paint splashes can lead to accidents

and soiling.

 Regularly provide for proper ventilation in the working

range and for sufficient fresh air throughout the com-

plete area.

 Wear safety glasses/goggles. This will protect your eyes

against splashing or ejected paint.

Wear appropriate work clothes. Paint is difficult to remove

from clothing.

Prevent the hose system from being constricted, e. g.,

through crushing, kinking or pulling! Do not stand on the feed

hose 2.

Keep the hose system away from heat sources.

Do not pull the hoses. Especially when moving the base unit,

do not pull it by the feed hose 2. Carry the base unit only by

the carrying handle 19.

Switching On (see figure D)

To save energy, only switch the power tool on when using it.

– Plug the mains plug into a socket outlet.

– Make sure that the pump lock 23 is engaged.

–To start the machine, push the On/Off switch 18 to the “I”

position.

– Grasp the paint applicator 3 or extension 1 by the respec-

tive handle and direct the paint roll 16 toward the surface

to be painted.

– Press the trigger switch 7 on the remote control 8.

Switching Off

– Release the trigger switch 7.

–To switch off the machine, push the On/Off switch 18 to

the “0” position.

– Pull the mains plug from the socket outlet.

– Disengage pump lock 23.

To relieve the lock tension, lightly push the pump lid 20 up-

ward, if required.

Working Advice

Painting

Before painting, moisten new or dried paint rolls with water.

When the paint roll is new or dry, it takes approx. six lanes un-

til the paint application is homogeneous and without streaks.

Filling an empty feed hose takes approx. one minute.

– Press the trigger switch 7 to apply a sufficient amount of

paint on the paint roll 16 and uniformly move the paint roll

up and down.

– Avoid interruptions within the surface to be painted.

Evenly guiding the paint roll will lead to a uniform surface

quality.

Regulating the Paint Amount during Painting

The paint amount can be regulated with the trigger switch.

– Press the trigger switch 7 until the application of paint on

the paint roll is homogeneous.

– Afterwards, release the trigger switch until the application

of paint on the painting surface is no longer opaque.

– Then, refill the paint chamber again with a sufficient

amount of paint (press trigger switch 7 approx. 5 sec-

onds).

Changing the Paint Roll (see figures E1 – E2)

Remove the paint roll from the paint applicator for cleaning or

when the paint roll is worn.

– Pull the roll holders 15 apart and allow the paint roll 16 to

slide out of the paint applicator 3.

To prevent the paint-soaked paint roll from drying out until it

has been washed out, it is best to immerse it into a water

bucket.

Appropriate new paint rolls can be found in our Bosch acces-

sories program.

Paint rolls from other manufacturers can also be used, when

the respective dimensions are observed (see “Technical Da-

ta”, page 17).

Insert a new paint roll as follows:

– Pull the roll axle 17 out of the old paint roll 16 and slide the

new paint roll on the roll axle until centred.

– Insert the roll axle 17 on one side in the roll holder 15 until

it fits.

– Press the paint roll into the roll holder of the other side.

The paint roll must be able to rotate freely.

Placing Down the Paint Applicator (see figure F)

– Place down the paint applicator 3 on the edge of the paint

bucket so that it rests on the bucket holder 14.

OBJ_BUCH-1513-004.book Page 18 Tuesday, November 26, 2013 4:07 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PPR 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PPR 250 Manual

Product: