544019

Bosch PLS 300 Set Manual

15
Zoom out
Zoom in
Previous page
1/130
Next page
English | 15
Bosch Power Tools 1 609 929 W68 | (21.6.11)
Operation
Sawing
Preparing for Operation
The saw station must be assembled depending on the respec-
tive sawing application:
– Sawing Panels
(e. g. laminate flooring panels)
–Sawing Profiles
(e. g. baseboards)
The use of screws/bolts is not required.
Panel (cross section) (see figures A1 – A3)
– Mount the support extensions 6 left and right to the base
unit 1.
– Depending on the workpiece size, mount the additional
supports 7 to the inner or outer guide of the support exten-
sions.
– Loosen the locking knob 3 a few turns.
– Turn the locking lever 10 of the guide rail leftward and fold
the guide rail 4 upward.
– Mark the desired cutting line on the workpiece.
– Place down the workpiece with the visible side flat against
the stop of the base unit 1.
– Fold the guide rail downward and align the workpiece to
the cutting line of mark 11.
– Lock the guide rail 4 with locking lever 10.
– Tighten the locking knob 3.
Panel (mitre cuts) (see figure B)
The mitre angle can be set in the range from 45° (left side) to
45° (right side).
– Loosen locking knob 12.
– Turn the guide rail 4 left or right until the angle indicator 13
indicates the requested mitre angle.
– Tighten the locking knob 12 again.
For swift and precise adjustment of standard mitre angles,
the guide rail engages at 0° and 45°.
– For additional worksteps, see “Panel (cross section)” on
page 15.
Profile (bevel cuts) (see figures C1–C3)
– Mount the support extensions 6 left and right at the front
position of the bridge 8.
– Fold the red end stop 9 by 180° to the rear.
– Loosen the locking knob 3 a few turns.
– Turn the locking lever 10 of the guide rail leftward and fold
the guide rail 4 upward.
– Mark the desired cutting line on the workpiece.
– Place down the workpiece flat
against the stop of the support
extensions 6.
– Fold the guide rail downward
and align the workpiece to the
cutting line of mark 11.
– Lock the guide rail 4 with locking lever 10.
– Tighten the locking knob 3
.
– Adjust the base plate of the jigsaw accordingly to the de-
sired angle.
Notes on the adjustment are given in the operating instruc-
tions of the jigsaw.
Note: The folded back red end stop 9 is used as the stop for
the base plate of the power tool.
Panel (lengthway cuts, recesses) (see figure D)
– Loosen the locking knob 3 a few turns.
– Remove the guide rail 4 and the bridge 8 from the base unit
1.
– Mount the support extensions 6 left and right to the base
unit 1.
– Depending on the workpiece length, mount the additional
supports 7 reversed (see figure D) into the inner or outer
guide of the support extensions.
f Take care that the cutting line in the notched area is be-
tween the additional supports, to ensure that you do
not saw into the saw station.
Note: When sawing lengthway cuts, the saw station is used
only as a supporting surface. The workpiece cannot be
clamped. Therefore, hold it tightly while sawing.
Working Advice
f Only use the saw blades recommended by Bosch (see
page 129). When using saw blades that are too thin, dan-
ger is given that the cut runs out of centre.
The base plate of the jigsaw must always be in the front posi-
tion.
The thickness of the material to be cut depends on the sawing
capacity of the respective jigsaw.
For further information, see the operating instructions of your
jigsaw.
To ensure optimal operational safety, the workpiece must al-
ways be affixed.
Sawing
– Position the base plate of the power tool in such a manner
on the guide rail 4 that you always saw in the direction of
locking knob 3.
– Switch on the machine.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
– Remove the power tool from the the guide rail and release
the workpiece.
Transport
– Remove the power tool before transporting.
OBJ_BUCH-1219-002.book Page 15 Tuesday, June 21, 2011 2:15 PM
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PLS 300 Set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PLS 300 Set in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info