544038

Bosch PCM 7 Manual

30
Zoom out
Zoom in
Previous page
1/346
Next page
30 | English
1 609 929 U75 | (19.7.10) Bosch Power Tools
Clamping the Workpiece (see figure F)
To ensure optimum working safety, the work-
piece must always be firmly clamped.
Do not saw workpieces that are too small to
clamp.
– Press the workpiece firmly against the
fence 6.
– Insert the material clamp 14 provided into
one of the holes 27 intended for it.
– Loosen the wing bolt 33 and adapt the mate-
rial clamp to the workpiece. Tighten the wing
bolt again.
– Firmly clamp the workpiece by turning the
threaded rod 34 in clockwise direction.
Loosening the Workpiece
– To release the material clamp, turn the
threaded rod 34 in anticlockwise direction.
Adjusting the Cutting Angle
f When adjusting the cutting angle, never ac-
tuate the On/Off switch 19. Danger of injury
if the machine should accidentally start.
f Before sawing, always tighten the clamping
lever 25. Otherwise the saw blade could be-
come jammed in the workpiece.
Adjusting Horizontal Mitre Angles
(see figure G)
The horizontal mitre angle can be set in the
range from 46° (left side) to 46° (right side).
– Release clamping lever 25, if tightened.
This allows the saw table to move freely.
– Turn the saw table 11 left or right by handle
9 until the angle indicator 35 indicates the
desired mitre angle.
– Tighten clamping lever 25 again.
For quick and precise setting of often used mi-
tre angles, the saw table 11 engages at the de-
tents of the following standard angles:
–45°/ –30°/ –22.5°/ –15°/
0°/ 15°/ 22.5°/ 30°/ 45°
Adjusting Vertical Bevel Angles (see figure H)
The vertical bevel angle can be set in the range
from 0° to 45°.
– Loosen the clamping lever 23.
– Tilt the tool arm by the handle 1 until the an-
gle indicator 36 indicates the desired bevel
angle.
– Hold the tool arm in this position and retight-
en the clamping lever 23.
For quick and precise setting of the standard
angles 0° und 45°, end stops are provided on
the housing.
– Loosen the clamping lever 23.
– For this, tilt the tool arm by the handle 1 to
the stop toward the right (0°) or to the stop
toward the left (45°).
– Retighten the clamping lever 23 again.
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On (see figure I)
–To start the machine, press the On/Off
switch 19 and keep it pressed.
Note: For safety reasons, the On/Off switch 19
cannot be locked; it must remain pressed during
the entire operation.
The tool arm can only be guided downward
when pressing lever 3.
–For sawing, you must additionally press lever
3 in addition to actuating the On/Off switch.
Switching Off
–To switch off the machine, release the
On/Off switch 19.
OBJ_BUCH-880-004.book Page 30 Monday, July 19, 2010 11:56 AM
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PCM 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PCM 7 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info