544038

Bosch PCM 7 Manual

31
Zoom out
Zoom in
Previous page
1/346
Next page
English | 31
Bosch Power Tools 1 609 929 U75 | (19.7.10)
Working Advice
General Sawing Instructions
f For all cuts, it must first be ensured that the
saw blade at no time can come in contact
with the fence, screw clamps or other ma-
chine parts. Remove possibly mounted aux-
iliary stops or adjust them accordingly.
Protect the saw blade against impact and shock.
Do not subject the saw blade to lateral pressure.
Do not saw warped/bent workpieces. The work-
piece must always have a straight edge to face
against the fence.
Long workpieces must be underlaid or support-
ed at their free end.
Marking the Cutting Line (see figure J)
A laser beam indicates the cutting line of the
saw blade. This allows for exact positioning of
the workpiece for sawing, without having to
open the retracting blade guard.
– For this, switch the laser beam on with the
switch 20.
– Align the cutting mark on your workpiece
with reference to the right-hand edge of the
laser line.
Position of the Operator (see figure K)
f Do not stand in a line with the saw blade in
front of the machine. Always stand aside of
the saw blade. This protects your body
against possible kickback.
– Keep hands, fingers and arms away from the
rotating saw blade.
– Do not cross your arms when operating the
tool arm.
Permissible Workpiece Dimensions
Maximal workpiece sizes:
Minimal workpiece sizes
(= all workpieces that can be clamped left or
right from the saw blade with the supplied ma-
terial clamp 14): 100 x 40 mm (length x width)
Cutting capacity, max. (0°/0°): 50 mm
Cutting Off
– Firmly clamp the workpiece as appropriate
for its dimensions.
– Adjust the requested horizontal and/or verti-
cal mitre/bevel angle.
– Switch on the machine.
– Press lever 3 and slowly guide the tool arm
downward by handle 1.
– Saw through the workpiece applying uniform
feed.
– Switch off the machine and wait until the
saw blade has come to a complete stop.
– Guide the tool arm slowly upward.
Replacing the Insert Plate
The red insert plate 7 can become worn after
long use of the power tool.
Replace defective insert plates.
– Bring the power tool into the working posi-
tion.
– Unscrew screws 8 using a Phillips screwdriv-
er and remove the old insert plate.
– Insert the new insert plate and and screw all
screws 8 in again.
Sawing Profile Strips
Profile strips/mouldings can be sawn in two dif-
ferent ways:
Always make trial cuts with the mitre angle set-
ting first on scrap wood.
Mitre/Bevel Angle Height x Width
Horizontal Vertical
0° 0°
50 x 110 mm
45° 0°
50 x 76 mm
0° 45°
37 x 110 mm
45° 45°
37 x 76 mm
– Placed against the fence
– Lying flat on the saw
table
OBJ_BUCH-880-004.book Page 31 Monday, July 19, 2010 11:56 AM
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PCM 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PCM 7 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info