79075

Bosch GWS 15-125 CITH Manual

24
Zoom out
Zoom in
Previous page
1/156
Next page
English | 251 609 929 L08 • 12.1.07
Approved Grinding Tools
All grinding tools mentioned in these operating
instructions can be used.
The permissible speed [rpm] or the circumferential
speed [m/s] of the grinding tools used must at least
match the values given in the table.
Therefore, observe the permissible rotational/cir-
cumferential speed on the label of the grinding tool.
Rotating the Machine Head
f Before any work on the machine itself, pull
the mains plug.
The machine head can
be rotated with respect
to the machine housing
in 90° steps. In this
manner, the On/Off
switch can be brought
into a more convenient
position for special
working situations,
e.g., for cutting opera-
tions using the cutting
guide with dust extrac-
tion protection guard
20/cut off stand or for
left-handed persons.
Completely unscrew the four screws. Rotate the
machine head carefully, without removing it from
the housing, to the new position. Screw in and
tighten the four screws again.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
When operating the machine with power from mobile
generators that do not have sufficient reserve capacity
or are not equipped with suitable voltage control with
starting current amplification, loss of performance or
untypical behavior can occur upon switching on.
Please observe the suitability of the power generator
being used.
Switching On and Off
To start the power tool, press the On/Off switch 4
forward and then down.
To lock-on the pressed On/Off switch 4, push the
On/Off switch 4 further forward.
To switch off the power tool, release the On/Off
switch 4, or when it is locked, briefly press the On/Off
switch 4 and then release it.
Switch Version without Lock-on
(country-specific):
To start the power tool, press the On/Off switch 4
forward and then down.
To switch off the machine, release the On/Off switch
4.
f Check grinding tools before using. The
grinding tool must be mounted properly and
be able to move freely. Carry out a test run
for at least one minute with no load. Do not
use damaged, out-of-centre or vibrating
grinding tools. Damaged grinding tools can
burst and cause injuries.
Kickback stop
In case of a sudden drop in speed,
e. g. jamming while carrying out a sep-
arating cut, the power supply to the
motor is interrupted.
To restart the operation, switch the
On/Off switch 4 to the Off position
and start the machine again.
Restarting protection
The restarting protection feature prevents uncon-
trolled restarting of the machine after an interruption in
the power supply.
To restart the operation, switch the On/Off switch
4 to the Off position and start the machine again.
max.
[mm] [mm]
D b d [rpm] [m/s]
115
125
150
6
6
6
22,2
22,2
22,2
11000
11000
9300
80
80
80
115
125
––
11000
11000
80
80
75 30 M 14 11000 45
b
d
D
D
D
b
d
OBJ_BUCH-165-003.book Page 25 Friday, January 12, 2007 9:16 AM
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 15-125 CITH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 15-125 CITH in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GWS 15-125 CITH

Bosch GWS 15-125 CITH User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info