Manual Bosch GNH 18V-64 (page 22 of 315) (All languages)

786282

Zoom out

Zoom in

1/315

22 | English

– Guiding along templates manufactured of hard material,

e.g. steel,

– Dropping on or sliding over the floor,

– Using as a hammer,

– Applying any kind of force.

Make sure to check whatever is below or behind your work-

piece. Do not shoot nails into walls, ceilings or floors, when

persons are behind them. The nails can burst through the

workpiece and injure someone.

Do not shoot a nail onto an already driven-in one. This could

cause the nail to deform, the nails could become jammed or

the power tool could move in an uncontrolled manner.

When the power tool is used under cold ambient conditions,

the first nails will be driven in slower than usual. Once the

power tool has warmed up during working, normal operating

speed will be regained.

Avoid pulling the trigger when the magazine is empty to min-

imise wear on the firing pin.

For longer work breaks or after finishing work, switch off the

power tool, remove the battery and empty the magazine if

possible.

Emptying the magazine (seefiguresC1–C2)

– With the nail pusher(13) pressed, pull the magazine

slider(14) backwards until the last nail is free; then care-

fully guide the magazine slider forwards to the beginning

of the magazine(12).

Note: Do not let the magazine slider snap back without guid-

ing it. This could damage the magazine slider and there is a

risk of getting your fingers caught.

– Turn the power tool so that the nails in the magazine slide

back to the magazine spring(17).

– Press the magazine spring down and allow the nails to

slide past the nail pusher(14) out of the magazine(12).

Adjusting the depth stop (seefigureD)

The driving depth of the nails can be set with the

thumbwheel(4).

– Empty the magazine(12).

–Nails are driven in too deep: To reduce

the driving depth, turn the

thumbwheel(4) anticlockwise.

–Nails are not driven in deep enough: To

increase the driving depth, turn the

thumbwheel(4) clockwise.

– Refill the magazine.

– Test the new driving depth on a test workpiece.

Repeat the worksteps as required.

Clearing jams (seefiguresE1–E2)

Single nails can become jammed in the shot duct. If this

should occur frequently, please contact an authorised Bosch

after-sales service centre.

Note: If the driver blade does not return after clearing a jam,

please contact an authorised Bosch after-sales service

centre.

– Release the trigger(5).

– Switch the power tool off and remove the battery(7).

– Empty the magazine(12).

– Press the clamping lever(3) down so that the shot duct

opens.

– Remove the jammed nail. Use a pair of pliers for this, if re-

quired.

– Close the shot duct, hang the clip of the clamping

lever(3) into the hooks on the shot duct and then push

the clamping lever up again.

– Refill the magazine.

Changing the workpiece protector (seefigureF)

The workpiece protector(1) at the end of the discharge

lock-off(2) protects the workpiece until the power tool is

correctly placed for the discharging procedure. The work-

piece protector can be removed and replaced

– Release the trigger(5).

– Switch the power tool off and remove the battery(7).

– Empty the magazine(12).

– Remove the workpiece protector from the discharge lock-

off.

– Push the new workpiece protector with the open end over

the discharge lock-off.

Note: A spare workpiece protector can be stored on top of

the magazine(12). For this, push the workpiece protector

into the storage compartment(10).

Transport and Storage

For transport, switch off the power tool; especially when us-

ing ladders or moving in an unusual stance or posture.

At the workplace, carry the power tool only by the handle(8)

and with the trigger(5) released.

Always store the power tool disconnected from the battery

and in a dry and warm location.

When not using the power tool for an extended period of

time, apply a fine oil coating to steel parts. This prevents the

formation of rust.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

1 609 92A 81N | (01.08.2022) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GNH 18V-64 in the language / languages: All languages as an attachment in your email.

The manual is 6.35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GNH 18V-64 Manual

Product: