Manual Bosch GNH 18V-64 (page 21 of 315) (All languages)

786282

Zoom out

Zoom in

1/315

English | 21

– Push the nail strip forwards in the magazine until the last

nail is positioned in front of the magazine spring(17).

Note: A lock function of the magazine slider prevents the

power tool from being started with an empty magazine. The

discharge lock-off cannot be pressed down and blank firing

is thus prevented.

– Press the pretensioned nail pusher(14) against the

magazine slider(13) and, at the same time, pull the

magazine slider completely to the end of the

magazine(12).

Note: The magazine slider must slide back with only low

force (finger-pressure). A tight-running magazine slider

causes the nails to be driven in at an incorrect angle.

– With the nail pusher(13) pressed, carefully guide the

magazine slider(14) forwards until the nail pusher is over

the last nail, thus pushing the nail strip in the magazine

completely to the front.

Note: Do not let the magazine slider snap back without guid-

ing it. This could damage the magazine slider and there is a

risk of getting your fingers caught.

Operation

Actuation systems

Single actuation with safety run

With this actuation system, the discharge lock-off(2) must

first be firmly pressed against the workpiece. A fastener is

not discharged until the trigger(5) is pulled.

Afterwards, further discharging procedures can only be ac-

tuated when the trigger and the discharge lock-off have been

set back to the starting position.

Contact actuation with automatic return

(GNH18V-64M)

With this actuation system, the trigger(5) must be pulled

first and held in this position. Afterwards, the discharge

lock-off must be firmly pressed against the workpiece in or-

der to discharge the fastener. (5)Further discharging pro-

cedures can be actuated by repositioning it elsewhere, while

the trigger is pushed.

In contact actuation mode, a nail can also be driven in with

single actuation.

Starting Operation

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the Battery

– Push the charged battery(7) into the battery bay of the

power tool until the battery is securely locked.

Switching On and Off (see figureB1B2)

– To switch on the power tool, press the on/off switch

button(18) for at least 1 second.

The on/off switch display(19) lights up green.

GNH18V-64M: If single actuation is activated, the

display(20) lights up white.

– To switch off the power tool, press the on/off switch

button(18) for at least 1 second.

Discharging the nails – single actuation (see

figureB1B2)

– Switch on the power tool.

– Firmly position the outlet(15) or the rubber workpiece

protector(1) on the workpiece until the discharge lock-

off(2) is pressed down completely.

– Afterwards, briefly press the trigger(5) and release it

again.

This discharges a nail.

– Allow the power tool to bounce back from the workpiece.

– For another driving procedure, completely lift the power

tool from the workpiece and position it firmly at the next

required location.

Discharging the nails – contact actuation (seefigureB1)

(GNH18V-64M)

– Switch on the power tool.

– Activate the contact actuation by briefly pressing the on/

off switch button(18).

The contact actuation display(21) lights up white.

– Press and hold the trigger(5).

– Firmly position the outlet(15) or the rubber workpiece

protector(1) on the workpiece until the discharge lock-

off(2) is pressed down completely.

This discharges a nail.

– For another discharging procedure, keep the trigger(5)

pressed and completely lift the power tool from the work-

piece. Replace it firmly in the next required position.

Working Advice

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Before starting work, always check that the safety and actu-

ation devices are functioning correctly and that all screws

and nuts are tightly seated.

If a power tool is defective or not functioning properly, dis-

connect it immediately from the power supply and contact

an authorised Bosch after-sales service centre. .

Do not perform any incorrect manipulations on the power

tool. Do not disassemble or block any components of the

power tool, such as the discharge lock-off.

Do not carry out "emergency repairs" with unsuitable means.

The power tool is to be maintained regularly and properly.

Avoid any tampering and damage to the power tool, e.g.

from:

– Imprinting or engraving,

– Retrofitting measures not approved by the manufacturer,

Bosch Power Tools 1 609 92A 81N | (01.08.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GNH 18V-64 in the language / languages: All languages as an attachment in your email.

The manual is 6.35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GNH 18V-64 Manual

Product: