651949

Bomann ES 184 CB Manual

55
Zoom out
Zoom in
Previous page
1/106
Next page
55
NOTE:
Do not place the steam nozzle in the centre of the jug but
close to the inner wall. This position is important for the
milk to get into whirling motion. We recommend using the
spout as guide for the steam nozzle.
9. Slowly open the steam control knob (3) towards “
” until
the desired amount of steam is set. Slightly move the jug
up and down. Close the steam control knob towards
“
” after the milk has frothed to the desired volume (approx.
50%).
NOTE:
• To further heat up the milk insert the steam nozzle
all the way to the bottom of the jug. Ensure that the
milk does not start boiling. In this case the foam will
collapse.
• The water is no longer hot enough if the indicator
lamp (10) turns off during frothing. Turn the steam
control knob towards “ ”. Wait until the indicator
lamp lights up again. Now continue frothing the
milk.
10. To remove the last coarse air bubbles knock the milk jug
after frothing carefully on the tabletop (as if you would set
it down a bit hard). Swivel the milk jug slightly around. This
helps to mix the foam after frothing. Now waste no time.
Pour the frothed milk slowly into the espresso.
11. Swivel the milk jug slightly around while pouring the frothed
milk slowly into the espresso.
NOTE:
• With a few artful movements you can draw designs
into the foam.
• Sprinkle cocoa powder or cinnamon to taste on the
foam.
12. IMPORTANT: Clean the steam nozzle immediately after
every use! When closing the steam control knob a vacuum
is created within seconds, which draws some milk into the
steam nozzle. Place your heat-resistant container under
the steam nozzle. Open the steam control knob briey for a
shot of steam to ush milk residue out of the steam nozzle.
Wipe the steam nozzle with a damp cloth.
13. Press push button (9) to
position to turn the steam
function off.
Cleaning
WARNING:
• Before cleaning, always remove the mains plug and wait until the
device has cooled down.
• Do not immerse the device in water. Otherwise this might result in
an electric shock or re.
• The steam nozzle is hot immediately after use!
CAUTION:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• Clean the casing with a slightly damp cloth without deter-
gents.
Group Head and Rubber Seal
Wipe group head and rubber seal with a damp cloth. Use a soft
nylon brush to remove stubborn residues. Dry with a soft cloth.
Accessories
Wash lter holder, lter inserts, drip tray grid, drip tray, measur-
ing spoon, water tank, steam nozzle pipe and steam nozzle
cover in warm sudsy water. Use a soft nylon brush, if neces-
sary. Rinse with clean water. Dry all parts with a soft cloth.
CAUTION:
These parts are not dishwasher-safe. Heat and aggressive
detergents can cause distortion and decolouration.
Water Tank
1. Open the lid to remove the water tank. Pull the tank with
both hands up and out. Replace the tank after cleaning and
drying.
NOTE:
The water tank has two hooks.
2. Hook the water tank into the two eyelets of the appliance.
3. Press the water tank slightly down for the valve to open.
Steam Nozzle
Clean steam nozzle, attached pipe and cover immediately after
use. Dry milk residue is difcult to clean.
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann ES 184 CB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann ES 184 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info